Philips VR 655 User Manual
Page 12
12
To record while you’re away, follow step 1 — 9
below.
FOR EACH STEP BELOW, YOU NEED TO FINISH
WITHIN 60 SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO BE RESTARTED
FROM STEP 1.
❍
Select Timer Mode
Press
TIMER.
The Timer
Recording menu appears.
❍
Select Programme mode
Press
PLAY
5 or
STOP
∞ to
select “QUICK PROGRAMM-
ING”, then press
OK/STATUS
.
The Quick Programming menu
appears.
• If you have already set 8 programmes, “ALL
PROGRAMS IN USE” appears and goes back to the
Timer Recording menu. If this happens, delete
unwanted programmes.
❍
Select Channel
Press
VCR CH
5 or ∞ to enter the TV channel.
• You can also use the
1
REW
/
CH-
and
¡
FF/CH+
on the front panel. However, press CH
before pressing these buttons. Otherwise, it functions as
REW
or FF.
• Holding down
VCR CH
5 or ∞ rapidly scans through
the channels.
• To record from external line input, press
VCR CH
5 or
∞
until “A/V REAR” appears on the TV screen.
❍
Select Start Time
Press
START +
or
–
(Number button
1
or
4
).
• Each time you press the button, the set time changes by
one-minute intervals. If you hold the button, the set
time changes by 30-minute intervals.
❍
Select Stop Time
Press
STOP +
or
–
(Number
button
2
or
5
).
• Each time you press the button, the
set time changes by one-minute
intervals. If you hold the button,
the set time changes by 30-minute
intervals.
Using On-Screen Display
You can display the VCR operating status on the TV
screen.
❍
Select VCR Set Up Mode
1 Press
VCR
.
2 Press
MENU
.
3 Press
PLAY
5 or
STOP
∞ to select “VCR SET
UP” then press
OK/STATUS
.
❍
Select On-Screen Mode
1 Press
PLAY
5 or
STOP
∞ to select “ON
SCREEN MODE”.
2 Press
FF
3. Each time you press the button, the
setting changes.
ON:
When you press a tape running button (Stop,
Play, etc.), the VCR status appears for 5
seconds.
COUNTER:
When you press a tape running button, the VCR
operating status appears for 5 seconds.
After 5 seconds, the VCR status disappears
except the time counter.
OFF:
The VCR operating status does not appear even
if you press a tape running button.
❍
Finish Setting
Press
MENU
.
To display the VCR status on the TV screen
manually, press
OK/STATUS
. The VCR status
appears for about 5 seconds.
• If “ON SCREEN MODE” is set to “OFF,” no
VCR status appears though you press
OK/
STATUS
.
1
2
3
4
5
QUICK PROGRAMMING
PROGRAM REVIEW
SELECT: CONFIRM: OK
END: TIMER
ONE TIME PROGRAM
PROGRAM 1
CHANNEL+/–
START +/– – –:– –
STOP +/– – –:– –
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
– –
ONE TIME PROGRAM
PROGRAM 1
CHANNEL+/–
START +/– 20:00
STOP +/– 22:00
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
12
Timer Recording
1
2
3
407/55A5
01.10.2, 8:57 AM
12