Panasonic PT-LM1U - Manual (Page 23)

44-E NGLISH
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 51, and reset “LAMP
RUNTIME” to “0”.
FUNC 1
This assigns a function to the
FUNC1 button of the ET-RM200
wireless remote control unit (sold
separately).
INDEX
Functions in the same way as the
INDEX WINDOW button on the
accessory card remote control unit.
(page 29)
KEYSTONE
Functions in the same way as when
“KEYSTONE” is selected from the
“MAIN MENU”. (page 34)
CONTROL KEY
To disable the buttons on the
projector, set “CONTROL KEY” to
“OFF”. A confirmation screen will
then be displayed. Select “OK” by
using I or H button. To use the
buttons on the projector, set to “ON”
by using the remote control unit.
AUTO POW.OFF
If no signal is input to the projector
for the duration of the period you
set, the projector will return to
standby mode. The period can be
set from 15 minutes to 60 minutes
in 5 minute intervals. If you don't
use this feature, set it to “DISABLE”.
This feature will not function when
using the “FREEZE” function.
POWER MEMORY
This sets the projector’s start up
status for when the power cord is
connected.
ON
The projector will start from the same
status as when the power cord was
disconnected. If the power cord was
disconnected during projection when
the projector was used the last time,
projection will start after the power cord
is connected.
OFF
The projector will be in standby mode.
E NGLISH -45
Adjustments
and
settings
F U N C 1 I N D E X
[
K E Y S T O N E
C O N T R O L K E Y O N
[
O F F
Setting up the security function
This projector is equipped with a security function. A password input screen
can be displayed, or a company URL can be set up and displayed at the
bottom of the projected image.
Press the F or G button on the
projector or remote control unit to
select “SECURITY”, then press the
ENTER button.
M E N U
K E Y S T O N E
P I C T U R E
P O S I T I O N
I N D E X W I N D O W
S H U T T E R
V O L U M E
L A N G U A G E
O P T I O N 1
O P T I O N 2
S E C U R I T Y
S E L E C T E N T E R E X I T
P A S S W O R D
O K R E T U R N A M E N D P A S S W D
N E W
C O N F I R M
O K R E T U R N
S E C U R I T Y
I N P U T P A S S W D O F F
A M E N D P A S S W D
T E X T D I S P L A Y O N
T E X T C H A N G E
S E L E C T A D J R E T R N
INPUT PASSWD
The password input screen can be
displayed when the power is turned
on. All of the controls other than the
POWER button are disabled unless
the password is entered correctly.
ON
“INPUT PASSWD” is enabled.
OFF
“INPUT PASSWD” is disabled. The
password input screen will not be
displayed when the power is turned
on.
AMEND PASSWD
Passwords can be changed. Press
the ENTER button to display the
“AMEND PASSWD” screen.
# Set a password by pressing the
F,G,I, and H buttons.
(A maximum of 8 buttons can be
set.)
$ Press the ENTER button.
% Enter the password again for
confirmation.
& Press the ENTER button.
Password change will be
completed.
(When you use the “SECURITY”
function for the first time)
Press the F, H, G, I, F, H, G
and I buttons in order, then press
the ENTER button.
(When a password change has
been made before)
Type in the changed password, then
press the ENTER button.
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the “LAMP
POWER” setting and the
number of times the power is
turned on and off).
P O W E R M E M O R Y O N
[
O F F