Powermate P1204 User Manual
Page 8
200-2667
8
Once installation planning is complete and all
necessary local permits are granted, installation of the
generator may begin. Within the following section
general recommendations are given for installing the
generator. However, installations are affected by local
site conditions, regional construction practices, material
availability, local or regional codes and/or other
variables. Therefore, recommendations included in this
manual are provided as a guide only and are not meant
to serve as detailed installation plans. All decisions
regarding installation and materials are at the discretion
of the licensed electrician's and licensed plumbers
performing the installation and/or the inspector
performing the final inspection as required by local or
regional code. Additionally, illustrations provided in this
manual are subject to ongoing revisions and shall not be
construed as blueprints.
For proper ventilation and maintenance, locate the
generator outdoors in an area that will allow a minimum
of three feet or more of clearance between the generator
and any other structure. Note: Check your local
building codes for clearance requirements for your
area.
When placing the generator, the direction of the
exhaust should be pointing away from windows, doors
and any ventilation system.
Insure that sufficient air flow is available to remove
the exhaust fumes and cool the generator properly.
NOTE: It would be extremely difficult, if not impractical,
to attempt a detailed coverage of every
installation possibility. For that reason, much of
the information is general in nature. Plan the
installation carefully. Information in this manual is
provided as a guide only and is not meant to
serve as a detailed installation plan. Illustrations
provided in the manual must not be construed as
blueprints.
NOTE: The generator has an engine fan that draws the
air in from the end panel slots, circulates it within
the enclosure and forces the air through the
side panels and the exhaust panel slots.
All local applicable codes, standards and regulations
must be followed for the installation of the generator.
Some areas may require building permits and/or detailed
sight inspections prior to approving the unit for use.
NOTE: Utility wiring from the house to power the
battery charger and other start assisting
components should be tightened on the
identified terminal block at a torque of 20 lb-
in. The wire size is to be selected according
to allowable ampacities given in Table 310-16
of the National Electric Code.
Signal wiring from the transfer switch is to be
18AWG multi-strand wire tightened on the
identified terminal block to a torque of 20 lb-in.
Power leads from the generator/circuit
breaker being wired to the transfer switch
should be tightened in the identified terminal
block to 120 lb-in. The wire size is to be
selected according to allowable ampacities
given in Table 310-16 of the National Electric
Code.
Field wiring of this unit must be conducted
by a licensed electrician.
C
CA
AU
UT
TIIO
ON
N
•
Covering or restricting the air passages on the
generator will cause the unit to overheat and
may create a fire hazard. Do not allow snow or
leaves to cover enclosure openings.
•
Leave a three foot or greater open area around
all sides of the unit. Check your local building
codes for clearance requirements for your area.
Do not plant trees or plants close to the unit.
•
Unit should be located such that it prevents
combustible material from accumulating under
the generator set.
G
G
G
G
E
E
E
E
N
N
N
N
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
O
O
O
O
R
R
R
R
II
II
N
N
N
N
S
S
S
S
T
T
T
T
A
A
A
A
L
L
L
L
L
L
L
L
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
L
L
L
L
O
O
O
O
C
C
C
C
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
A
A
A
A
N
N
N
N
D
D
D
D
G
G
G
G
E
E
E
E
N
N
N
N
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
O
O
O
O
R
R
R
R
P
P
P
P
L
L
L
L
A
A
A
A
C
C
C
C
E
E
E
E
M
M
M
M
E
E
E
E
N
N
N
N
T
T
T
T
W
WA
AR
RN
NIIN
NG
G
•
Hazardous voltage can cause severe injury or
death. Electrocution is possible whenever
electricity is present. Open the main circuit
breaker of all power sources before servicing
the equipment. Configure the installation to
electrically ground the generator set, transfer
switch and related equipment and electrical
circuits to comply with applicable codes and
standards. Never contact electrical leads or
appliances when standing in water or on wet
ground because these conditions increase the
risk of electrocution.
•
The exhaust from this product is extremely hot
and remains hot after shutdown. High grass,
weeds, brush, leaves, or other combustible
materials, must remain clear of the exhaust.
Such materials may ignite and burn from the
heat of the exhaust system.
D
DA
AN
NG
GE
ER
R
•
The generator engine exhaust fumes contain
carbon monoxide, which can be DEADLY. This
dangerous gas, if breathed in sufficient
concentrations, can cause unconsciousness or
even death. The generator must be installed
properly, in strict compliance with applicable
codes and standards. Following installation,
you must do nothing that might render the
generator unsafe or in noncompliance with
such codes and standards.