Powermate P1204 User Manual
Page 18
200-2667
18
After completing all installation procedures, read and
understand the operating instructions for the generator
controller. Know how the control panel operates, what to
expect when activating control panel switches and how
to shut the generator off in the event of an emergency.
Before starting the generator for the first time, check off
all items on the following list, then follow the given
procedure to verify correct operation of the generator.
Is unit level?
Is adequate free air space (3 feet minimumor
greater,check your local building codes for clearance
requirements for your area.) available on all sides of
the enclosure?
Are all cabinet openings free from blockage?
Is the exhaust directed away from dwellings, dwelling
air intakes, or combustible materials?
Are the fuel supply lines and internal generator fuel
connections leak-free?
Is fuel supply pressure within specifications?
Is the regulator connection properly configured for
the fuel supplied?
Is an approved transfer switch used to prevent
backfeed into utility lines?
Are electrical connections tight, and properly
connected?
Are electrical conductors sized properly?
Is a properly sized engine cranking battery correctly
installed?
Is the battery maintenance charger plugged in and
operating correctly?
Are all protective covers installed and tightened?
Are all tools clear of moving or electrically live parts?
Is the installation inspected and approved as
required by local or regional code?
Once all items on the checklist are marked off,
complete the initial startup using the listed steps.
1. Press the OFF button on the control panel of the
generator.
2. Move the main line circuit breaker handle on the
generator to the OFF position.
3. Check the utility, or preferred, power supply to the
transfer switch following the instructions provided by
the switch manufacturer.
4. Ensure utility power to the transfer switch is shut off.
5. Return to the generator and open any manual shutoff
valves in the fuel supply system.
6. Press the MANUAL button on the control panel. The
generator should crank and start.
7. Allow the generator to run for approximately three (3)
minutes, then move the main line circuit breaker
handle to the ON position.
8. Check across the circuit breaker of the main line
power output block (Red to Black) for proper
frequency and voltage. Frequency should read
approximately 62.5 Hz and voltage between 240 and
245 volts at no load conditions.
9. Adjust no load speed as required to meet
approximately 62.5 Hz.
10. Shut the generator down by pressing the OFF button
on the control panel.
11. Restore utility power to the transfer switch.
12. Press the AUTO button on the control panel to set
the generator to automatic.
13. Inspect the site to ensure no packaging or installation
materials remain within or against the generator.
14. Replace all covers on the generator.
15. Place the generator into service by pressing the
AUTO button on the control panel.
A standby generator is an engine driven air cooled
system to convert the energy contained in either liquid
propane vapor or natural gas to electrical power. When
coupled with an automatic transfer switch to monitor for
failure of utility power, the unattended system can start,
stop and transfer between sources to insure a nearly
seamless supply of power. The generator is housed in a
weather resistant, sound attenuated enclosure for
outdoor installation only.
Before installing and starting the generator, become
familiar with the controls and operational features of the
generator. Know how the control panel operates, what to
expect when activating control panel switches and how
to shut the generator off in the event of an emergency.
F
F
F
F
II
II
R
R
R
R
S
S
S
S
T
T
T
T
T
T
T
T
II
II
M
M
M
M
E
E
E
E
S
S
S
S
T
T
T
T
A
A
A
A
R
R
R
R
T
T
T
T
U
U
U
U
P
P
P
P
D
DA
AN
NG
GE
ER
R
•
Contact with high voltages present in
generators and utility systems can cause
severe electric shock or death. Avoid contact
with all live components.
•
Allow only qualified generator service
technicians or licensed electrician's to perform
initial system start-up.
D
DA
AN
NG
GE
ER
R
•
Generator is now supplying dangerous
voltages. Use extreme caution performing
electrical checks.
C
CA
AU
UT
TIIO
ON
N
•
Failure to set the controller to AUTO before
leaving the generator renders the generator
unavailable for automatic standby service.
G
G
G
G
E
E
E
E
N
N
N
N
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
O
O
O
O
R
R
R
R
O
O
O
O
P
P
P
P
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N