beautypg.com

Specifications, Specifi cations, Lang - 5 lang - 4 français dansk english – Panasonic SC-AK450 User Manual

Page 19

background image

19

RQT8043

RQTV0191

LANG - 5

LANG - 4

FRANÇAIS

DANSK

ENGLISH

AMPLIFIER SECTION

FTC Output power

THD 10%, both channels driven

50 Hz to 3 kHz

(Low channel)

95 W per channel (3 Ω)

3 kHz to 12 kHz

(High channel)

95 W per channel (3 Ω)

Total FTC Bi-Amp power 380

W

RMS output power

THD 10%, both channels driven

1

kHz

(Low channel)

115 W per channel (3 Ω)

10

kHz

(High channel)

115 W per channel (3 Ω)

Total Bi-Amp power 460

W

FM/AM TUNER, TERMINALS SECTION

Preset station

FM 20 stations

AM 15 stations

Frequency Modulation (FM)

Frequency range

87.9 to 107.9 MHz (200 kHz step)

87.5 to 108.0 MHz (100 kHz step)

Sensitivity

4.0 µV (IHF)

S/N 26 dB 2.2

µV

Antenna terminal(s) 75

Ω (unbalanced)

Amplitude Modulation (AM)

Frequency range

520 to 1710 kHz (10 kHz step)

Sensitivity

S/N 20 dB (at 1000 kHz) 560

µV/m

Music Port input jack

Terminal

Stereo, 3.5 mm (

1

/

8

˝) jack

Sensitivity

100 mV, 4.7 kΩ

Phone jack

Terminal

Stereo, 3.5 mm (

1

/

8

˝) jack

XM ready

XM mini Tuner and Home Dock

CASSETTE DECK SECTION

Track system

4 track, 2 channel

Heads

Record/playback

Solid permalloy head

Erasure

Double gap ferrite head

Motor

DC servo motor

Recording system

AC bias 100 kHz

Erase system

AC erase 100 kHz

Tape speed

4.8 cm/s (1

7

/

8

ips)

Overall frequency response (+3 dB, –6 dB) at DECK OUT

NORMAL

35 Hz to 14 kHz

S/N Ratio

50 dB (A weighted)

Wow and fl utter 0.18%

(WRMS)

Fast forward and rewind time

Approx. 120 seconds with

C-60 cassette tape

DISC SECTION

Disc played [8 cm (3˝ ) or 12 cm (5˝ )]
(1)

CD-Audio

(CD-DA)

(2) CD-R/RW (CD-DA, MP3

*

formatted disc)

(3)

MP3

*

*

MPEG-1 Layer 3, MPEG-2 Layer 3

Bit rate

MP3

32 kbps to 320 kbps

Sampling frequency

MP3

32 kHz, 44.1 kHz, 48 kHz

CD-DA 44.1

kHz

Decoding

16 bit linear

Digital fi lter 8

fs

D/A converter

MASH (1 bit DAC)

Pick up

Wavelength 780

nm

Beam Source Semiconductor

laser

Audio output (Disc)

Number of channels

2(Stereo) (FL, FR)

OPTION PORT SECTION

Option

Port Version

1

SPEAKER SECTION

Type

2 way, 2 speaker system (Bass refl ex)

Speaker(s)

Woofer

16 cm (6

1

/

2

˝) cone type

Tweeter

6 cm (2

3

/

8

˝) cone type

Impedance

HIGH 3

Ω

LOW 3

Ω

Input power (IEC)

HIGH

115 W (Max)

LOW

115 W (Max)

Output sound pressure level

84 dB/W (1.0 m)

Cross over frequency

2.6 kHz, 10 kHz

Frequency range

35 Hz to 25 kHz (–16 dB)

27 Hz to 28 kHz (–10 dB)

Dimensions (WxHxD)

219 x 330 x 216 mm

(8

5

/

8

˝ x 13˝ x 8

1

/

2

˝)

Mass 2.9

k

g (6.4 Ib.)

GENERAL

Power supply

AC 120 V, 60 Hz

Power consumption

127 W

Dimensions (WxHxD)

250 x 330 x 323 mm

(9

27

/

32

˝ x 13˝ x 12

23

/

32

˝)

Mass 7.1

k

g (15.7 lb.)

Operating temperature range

+5 to +35 °C (+41 to +95°F)

Operating humidity range

5 to 90 % RH (no condensation)

Power consumption in standby mode:

0.28 W (Approx.)

Note:
1. Specifi cations are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum

analyzer.

3. The labels “HIGH” and “LOW” on the rear of the speakers refer to

High frequency and Low frequency.

Specifi cations

Disc trays

Disc tray(s) cannot open.
“CHGR ERR” is displayed.

Press [

y/I, POWER] to release the jammed tray(s) as the unit will switch off. Switch it on again and

the tray(s) will initialize to the previous tray(s) condition.
If this still does not fi x the problem, please consult the dealer.

Remote control

Remote control doesn’t work.

Check that the batteries are inserted correctly.

5

Replace the batteries if they are worn.

Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2)
2 While pressing and holding down [

y/I, POWER] on the main unit, reconnect the AC power supply cord.

“– – – – – – – – –” appears on the display.

3 Release [

y/I, POWER].

All the settings are returned to the factory preset.
You will need to reset the memory items.

RQTV0191-1P_1EN.indd 19

RQTV0191-1P_1EN.indd 19

2/23/07 6:09:51 PM

2/23/07 6:09:51 PM