Kenwood KRF-V6090D - Manual (Page 17)

17 EN
If you have selected “NML” as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
connected to this model.
2 CNTR OFF : Center speaker setting mode to this
model is OFF.
9 Press the SETUP key again to accept the setting.
•The surround speaker setting indication “SURR NML” appears.
0 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround speaker setting.
If you have selected “LRG” as the Center speaker setting,
1 SURR NML (normal) : Average size Surround speakers are
connected to this model.
2 SURR LRG (large) : Large Surround speakers are connected
to this model.
3 SURR OFF : Surround speaker setting mode to this
model is OFF.
If you have selected other than “LRG” as the Center speaker
setting,
1 SURR NML (normal): Average size Surround speakers are
connected to this model.
2 SURR OFF : Surround speaker setting mode to this
model is OFF.
• When the setting “SURR OFF” is selected, the procedure skips
to step #.
! Press the SETUP key to accept the setting.
• The Surround Back speaker setting indication “BS” appears.
@ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the appropriate Surround Back speaker setting.
If you have selected “LRG” as the surround speaker setting,
1 BS NML (normal
: Average size Surround back speakers are
connected to this model.
2 BS LRG (large) : L a r g e S u r r o u n d B a c k s p e a k e r i s
connected to this model.
3 BS OFF : Surround Back speaker setting mode to
this model is OFF.
If you have selected “NML” as the Surround speaker setting,
1 BS NML (normal) : Average size Surround Back speakers are
connected to this model.
2 BS OFF : Surround Back speaker setting mode to
this model is OFF.
(VR-906/KRF-V6090D only)
If you have selected “LRG” or “NML” as the surround back
speaker setting.
1 SPEAKER : Surround Back signal will be output from
SURROUND BACK speaker terminal, and SURR
BACK L/ SURR BACK PRE OUT terminal as
monaural.
2 PRE OUT : Surround Back signals will be output from SURR
BACK L/ SURR BACK and SURR BACK R PREOUT
terminals as stereo.
# Press the SETUP key again to accept the setting.
• The subwoofer re-mix setting indication “SW RE-MIX” scrolls
across the display.
• If subwoofer is turned OFF, subwoofer re-mix setting is not
visible.
Preparing for surround sound
$ Use the MULTI CONTROL knob or MULTI CONTROL %/fi
keys to select the appropriate Subwoofer re-mix setting.
1 RMX ON : Subwoofer re-mix set mode to this model is ON.
2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.
% Press the SETUP key to accept the setting.
4
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• In step 4 and 5, indications appear only for the selected channels
of the speakers that require adjusting.
1 Press the SETUP key to begin TEST TONE.
• This model enters the speaker volume level adjustment mode.
The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or MULTI CONTROL
%/fi keys.
1 AUTO
2 MANUAL
2 Press the SETUP key again to select either AUTO or MANUAL.
Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to adjust the volume level of the test tone output from the
speaker channel to be adjusted.
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
¶
• If any of the speaker is set as OFF during SP SET UP, the TEST
TONE adjustment for the speaker will be skipped.
(VR-906/KRF-V6090D only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared.
3 Press the SETUP key.
• The test tone is turned off. This model enters the mode for
inputting the distance to the speakers.
4 For MANUAL selection, press the SETUP key each time to
select the speaker channel.
5
Input the distance to the speakers.
1 Select the DISTANCE from the set up displays and press the
SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front Left speaker (L) : ____ feet (meters)
Distance to Center speaker (C) : ____ feet (meters)
Distance to Front Right speaker (R) : ____ feet (meters)
Distance to Surround Right (RS) : ____ feet (meters)
Distance to Surround Back Right (RB) : ____ feet (meters)
Distance to Surround Back (BS)
: ____ feet (meters)
Distance to Surround Back Left (LB) : ____ feet (meters)
Distance to Surround Left (LS) : ____ feet (meters)
Distance to Subwoofer (SW) : ____ feet (meters)
(VR-906/KRF-V6090D only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB” and “LB” are not appeared but “BS” is appeared.
Continued to next page
04.11.25, 19:02 17