Troubleshooting guide – Kenwood DPX-3050 User Manual
Page 32
English
— 32 —
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
General
?
The power does not turn ON.
01
✔ The fuse has blown.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
✔ No ACC position on vehicle ignition.
02
☞ Connect the same wire to the ignition as the battery wire.
?
Nothing happens when the buttons are pressed.
04
✔ The computer chip in the unit is not functioning normally.
☞ Press the reset button on the unit (page 4).
?
There’s a source you can’t switch.
05
✔ There’s no tape inserted.
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
✔ There’s no CD inserted.
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
✔ The Disc changer isn’t connected.
08
☞ Connect the Disc changer. If the Disc changer isn’t connected to
it's input terminal, You can't switch to an external disc source.
?
The memory is erased when the ignition is turned OFF.
10
✔ The battery wire has not been connected to the proper terminal.
☞ Connect the wire correctly, referring to the section on
✔ The ignition and battery wire are incorrectly connected.
11
☞ Connect the wire correctly, referring to the section on
?
No sound can be heard, or the volume is low.
✔ The fader or balance settings are set all the way to one side.
21
☞ Center the fader and balance settings.
✔ The input/output wires or wiring harness are connected incorrectly.
22
☞ Reconnect the input/output wires or the wiring harness correctly.
See the section on
✔ The cassette tape is bad.
23
☞ Try playing another cassette tape. If works fine, the first tape was
bad.
?
The sound quality is poor or distorted.
25
✔ One of the speaker wires is being pinched by a screw in the car.
☞ Check the speaker wiring.
✔ The tape head is dirty.
26
☞ Clean the tape head.
✔ The speakers are not wired correctly.
27
☞ Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
?
Non-fading setting can’t be done.
28
✔ The
☞ Set it on Non-fading preout.
?
The text is not scrolled.
31
✔ This is because eight or less characters are displayed.
☞ If all the characters are displayable on the display part, the text is
scrolled once when the display switches, and after that, the text
is not scrolled.
?
The Security Code item isn’t displayed in the Function System.
32
✔ The Security Code function is already activated.
☞ When the Security Code function is activated it isn’t displayed in
the Function items.
?
The Touch Sensor Tone doesn’t sound.
34
✔ The preout jack is being used.
☞ The Touch Sensor Tone can’t be output from the preout jack.
?
Even though the vehicle light switch is turned ON, the unit’s display
won’t dim.
36
✔ The dimmer wire isn’t connected.
☞ Connect the dimmer wire correctly.
?
The display color changes subtly.
38-2
✔ This is because the temperature is different than the temperature
when the setting was done.
☞ The display color condition changes subtly according to the
ambient temperature.
Troubleshooting Guide
DPX-MP4050(M-TKR)(E) 2003.02.14 09:03 AM Page 32