Scag Power Equipment SWU - Manual (Page 23)

19
Ref. Part
No. No.
Description
1 461368 Cutter Deck With Decals 48"
461373 Cutter Deck With Decals 52"
2 04017-27 Capscrew, 3/8-16 x 1.0" Serrated Flange
3 04021-05 Lock Nut, 3/8-16 Center Lock
4 48100-15 Bushing, 376 ID Oilite
5 481632 Wheel, Anti-Scalp
6 422478 Bracket, Anti-Scalp Wheel
7 04003-26 Bolt, Carriage 3/8-16 x 4.0"
8 04021-09 Hex Nut, 3/8-16 Elastic Stop
9 04043-04 Flatwasher, 3/8 (.938 x .391 x .105) Grade 8
10 48224 Ball Bearings
11 461175 Idler Arm RH
12 43503 Pivot, Idle - Short
13 04003-04 Bolt, Carriage 5/16-18 x 1.0"
14 422713 Base, Idler Pivot
15 04001-31 Capscrew, Hex Head 3/8-16 x 2.50"
16 04001-45 Capscrew, Hex Head 3/8-16 x 2.0"
17 04001-136 Capscrew, Hex Head 3/8-16 x 1.50" Grade 8
18 04019-04 Nut, 3/8-16 Serrated Flange
19 48181 Pulley, Idler
20 481838 Pin Assembly (Incl. 21 & 23)
21 04020-25 Nut, 3/8-24 Jam
22 43512 Spacer, Deck Adjustment Pin
23 481539 Rod End, Male 3/8-24
24 46631 Spindle Assembly
25 43309 Spacer, Spindle
26 04001-41 Bolt,Hex Head 5/8-11 x 9.50"
27 04040-10 Flatwasher, 5/8 W
28 481706 Cutter Blade 16-1/2" 48"
28 481707 Cutter Blade 18" 52"
28A 481710 Cutter Blade 16-1/2" Hi Lift 48"
28A 481711 Cutter Blade 18" Hi Lift 52"
29 04001-10 Bolt, Hex Head 5/16-18 x 1.50"
30 43298 Spindle Shaft
31 481024 Seal, Cutter Spindle - Top
32 481022 Tapered Bearings (Two)
33 48114-04 Grease Fitting
34 43294 Spindle Housing
Ref. Part
No. No.
Description
48" & 52" CUTTER DECKS
35 48677 Relief Fitting, Cutter Spindle
36 43312 Spacer Outside
37 43296 Spacer, Inside
38 481025 Seal, Cutter Spindle - Bottom
39 43297 Spindle Bushing
40 481035 Nut, Spindle
41 481625-01 Wing Nut, 3/8-16
42 451118 Roller Shaft
43 04001-12 Bolt, Hex Head 5/16-18 x 1.0" Front
43 04001-11 Bolt, Hex Head 5/16-18 x 1.50" Rear
44 04060-08 Pin, Slotted Spring 3/16 x 1.50"
45 43515 Pin, Deck Adjustment Rear
46 48926 Tapered Hub
47 48038 Guide, Roller
48 48924 Pulley
49 48923 Pulley, 5.75 Double Groove
50 481922 Belt, Deck Drive
51 04015-14 Capscrew, Socket Head 1/4-20 x 1.375"
52 04020-09 Hex Nut, 5/8-11
53 48087 Belt, RH Blade Drive 48"
53 48285 Belt, RH Blade Drive 52"
54 422745 Belt Cover, RH
55 04001-62 Capscrew, Hex Head 3/8-16 x 3.25"
56 461174 Idler Arm Weldment
57 04001-51 Capscrew, Hex Head 3/8-16 x 3.75"
58 461291 Discharge Chute, Nylon
59 04019-03 Nut, 5/16-18 Serrated Flange
60 481597 Spring, Deck Idler
61 04001-154 Bolt, Hex Head 5/16-18 x 4.75"
62 482245 Spring, Chute Return
63 04021-09 Nut, 3/8-16 Elastic Stop
64 04021-10 Nut, 5/16-18 Elastic Stop
65 04001-31 Bolt, Hex Head 3/8-16 x 2.50"
66 04063-08 Key, 1/4 x 1/4 x 2.0"
67 481962 Pulley, Idler
68 43510 Pivot, Idler - Long
69 422744 Belt Cover LH
70 04110-03 U-Nut, 3/8-16
71 04030-03 Lockwasher, 5/16 (.317 x .586 x .078)
* Common hardware which should be purchased locally. All bolts are Grade 5 plated, all other fasteners zinc plated.