Scag Power Equipment STC - Manual (Page 41)

37
Section 8
1 461310 Cutter Deck (Includes decals) x
461311 Cutter Deck Advantage (Not Shown) x
461313 Cutter Deck Advantage (Not Shown) x
2 04003-04 Bolt, Carr. 5/16-18 x 1” x x
3 04019-04 Nut, 3/8-16 Serrated Flange x x
4 481625-01 Wing Nut, 3/8-16 x x
5 481632 Anti-Scalp Wheel x x
6 04003-26 Bolt, Carriage 3/8-16 x 4” x x
7 422478 Bracket, Anti-Scalp Wheel x x
8 04017-27 Bolt, Serrated Flange 3/8-16 x 1” x x
9 04040-10 Flatwasher 5/8” x x
10 04021-05 Locknut, 3/8-16 Center Lock x x
11 461291 Discharge Chute x
461295 Discharge Chute (“48A & 52A” Advantage) x x
12 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2” x x
13 04021-10 Nut, Elastic Stop 5/16-18 x x
14 04020-09 Nut, 5/8-11 UNC x x
15 45944 Shaft, Roller x x
16 04001-41 Bolt, Hex Head 5/8-11 x 9-1/2” x x
17 48038 Roller, Rear x x
18 04001-154 Bolt, Hex Head 5/16-18 x 4-3/4” x x
19 04063-08 Key, 1/4 x 1/4 x 2” x x
20 482718 Spring, Idler x x
21
04043-04 Flatwasher, 3/8” x x
22 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2” x x
22A 04001-12 Bolt, Hex Head 5/16-18 x 1-3/4” x x
23 04019-03 Nut, Serrated Flange 5/16-18 x x
24 04001-01 Bolt, Hex Head 1/2-20 x 3/4” x x
25 48100-15 Bushing, .376 ID Oilite x x
26 04030-03 Lockwasher 5/16” x x
27 04040-15 Flatwasher 5/16” x x
28 04001-136 Bolt, 3/8-16 x 1-1/2” Grade 8 x x
29 04021-09 Nut, Elastic Stop 3/8-16 x x
30 04001-51 Bolt, Hex Head 3/8-16 x 3-3/4” x x
31 04001-62 Bolt, Hex Head 3/8-16 x 3.25” x x
32 04001-136 Bolt, Heax Head 3/8-16 x 1-1/2 Grade 8 x x
33 04110-03 U-Nut, 3/8-16 x x
34 46631 Spindle Assembly x x
35 43298 Shaft, Spindle x x
36 481024 Seal Upper x x
37 481022 Bearing Assembly x x
38 48114-04 Grease Fitting x x
48", 48A”& 52A" CUTTER DECKS
Ref. Part
No. No.
Description 48 52
Ref. Part
No. No.
Description 48 52
39 48677 Valve, Grease Relief x x
40 43294 Housing, Spindle x x
41 43312 Spacer, Outside x x
42 43296 Spacer, Inside x x
43 481025 Seal, Lower x x
44 43297 Bushing, Bottom x x
45 481035 Nut, Special 1-1/16 - 18 x x
46 43309 Spacer, Spindle x x
47 481706 Cutter Blade 16.5” x
481707 Cutter Blade 18” x
48 422713 Pivot, Idler Base x x
49 48224 Bearing x x
50 461314 Idler Arm x x
51 461175 Idler Arm x x
52 423109 Belt Cover LH (48 & 48A) x
52A 423110 Belt Cover RH (48 & 48A) x
52 423119 Belt Cover LH (52A) x
52A 423120 Belt Cover RH (52A) x
53 48926 Hub, Tapered 1-1/8” Bore x x
54 481962 Pulley, Idler 5.0” x x
55 482217 Pulley, Idler 5.0” x x
56 482148 Pulley 4.75” x
481435 Pulley 5.35” x
57 482149 Pulley Double Groove 4.75” x
482150 Pulley Double Groove 5.35” x
58 48100-06 Bushing, .753” ID x x
59 461036 Push Arm (Includes 58, 64, 60, 62) x x
60 04020-16 Nut, 5/8-18 UNF x x
61 04021-13 Nut, Elastic Stop 5/8-11 x x
62 48763 Rod End, 5/8 Male RH Thread x x
63 04001-79 Bolt, Hex Head 5/8-11 x 4-1/2” x x
64 48114-08 Grease Fitting, 90 Degree x x
65 482137 Belt, Cutter Deck Drive (48” and 48A”) x
482139 Belt, Cutter Deck Drive (52A”) x
66 482138 Belt, RH Cutter Deck (48” and 48A”) x
482140 Belt, RH Cutter Deck (52A”) x
67 481050 Spring, Discharge Chute x x
68 451240 Push Arm Shaft x x
69 04015-14 Socket Head Capscrew, 1/4-20 x 1-3/8” x x
70 422599 Turbo Baffle, Bolt On x
422600 Turbo Baffle Bolt On x
71 04001-09 Bolt, Hex Head 5/16-18 x 1” x x
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.