beautypg.com

Zone 2 operation, Chapter 5, Audio connections – Sunfire TGR401 User Manual

Page 48: Video connections, Indicators, Turning on zone 2, Zone 2 osd menu, Binding posts menu, User's manual

background image

User's Manual

48

CHAPTER 5

Zone 2 Operation

If you have a pair of speakers in a

second room or area (Zone 2), they
can play a stereo source independent
of whatever is playing in the Home
Theater room (Main Zone). You can
also play the same source as selected
in the Main Zone.

The Zone 2 speakers can be pow-

ered by two of the TGR-401's internal
ampli¿ ers, if you enable "Powered Z2"
in the Binding Posts menu. The ampli-
¿ ers that power the surround-back
speakers are switched to play the
Zone 2 speakers instead. An external
power ampli¿ er can be used to power
the Zone 2 speakers.

Zone 2 plays stereo sources, and is

unaffected by the DSP, Sonic Hologra-
phy, surround modes or bass man-
agement.

Audio Connections

The connections for Zone 2 are

shown on page 23.

Note: Zone 2 can play analog

sources independent of what is play-
ing in the Main Zone. It cannot play
from a digital-only source unless that
input is selected and playing in the
Main Zone. To play a source such as
a DVD player in Zone 2 independent
of the Main Zone, make sure you
connect the player's L-R analog audio
output to the TGR-401.

Video Connections

Zone 2 has a composite video

output that can connect to a video
monitor in your other room. This will
only play if the selected source also
has composite video.

Indicators

The front panel has

a green LED to show
the Zone 2 status.
This LED is always on
when Zone 2 is on. If
it is off, there will be
no output to Zone 2.

Turning on Zone 2

With the remote set to operate the

TGR-401, press the ZONE 2 button.
The remote's POWER, VOLUME and
MUTE buttons then work for Zone 2.

Note: Zone 2 can also be turned

on and adjusted without using the
remote. Press the Zone 2 button on
the TGR-401 front panel followed by
Power to turn it on (or off), or adjust
the input source or volume. After 8
seconds of inactivity, the front panel
will revert back to control of the Main
Zone.

Zone 2 operations will work even if

the Main Zone is off.

SETUP

CHOICES

INPUTS
SPEAKERS
VIDEO
MAIN ZONE
ZONE 2
CONTROL
DIGITAL OUT

DNMX/THRU

DIMMER LOW/MED/HI

MAIN MENU
TRIMS
TONE CONTROLS
MODES
PRESETS
SETUP

SPEAKERS
AUTO SETUP
SPEAKER SIZE
DISTANCE
LEVEL CALIBRATION
EQ
BINDING POSTS

BINDING POSTS

CHOICES

AMP SECTION

ON

ON, OFF

FRONT

ON

ON, OFF

SURROUND

ON

ON, OFF

CFG POST

OFF

OFF, FRONT, SURR

POWERED Z2

OFF

ON/OFF

ZONE 2

CHOICES

FIXED VOLUME

NONE

NONE, 0.0 - 100.0

PWR UP MAX VOL

100.0

0.0 - 100.0

PWR UP MIN VOL

0.0

0.0-100.0 MUST BE LESS THAN POWER UP MAX VOLUME

MAX VOLUME

100.0

0.0-100.0 MUST BE MORE THAN POWER UP MAX VOLUME

PWR UP SOURCE

LAST

LAST, INPUT 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12

BASS

0

+14 TO -14, 2 DB STEPS

TREBLE

0

+14 TO -14, 2 DB STEPS

BALANCE

0

-20 TO +20, 1 DB STEPS

Zone 2 OSD menu

The ZONE 2 menu allows you to

customize Zone 2 to suit:

FIXED: Set the Zone 2 volume at this

¿ xed level.

PWR UP MAX VOL: Set the Zone 2

turn-on volume so it will not come
on higher than this.

PWR UP MIN VOL: Set the Zone 2

turn-on volume so it will not come
on lower than this level.

MAX VOLUME: Set the Zone 2 vol-

ume so it cannot be higher than
this level.

BASS: Adjust the bass with up to 14

dB of boost or cut.

TREBLE: Adjust the treble with up to

14 dB of boost or cut.

BALANCE: Adjust the balance with up

to 20 dB or adjustment either side.

Binding Posts menu

POWERED Z2: Set to ON for the

Zone 2 binding posts to supply
speaker-level power to your Zone
2 speakers

This manual is related to the following products: