JVC GET0635-003A - Manual (Page 3)

3
1 2 3 Repeat step 2 if necessary.
• To return to the previous menu, press BACK.
• To exit from the menu, press DISP or MENU.
Category Menu item Selectable setting, [ Initial: Underlined ]
DEMO
DEMO • DEMO ON
• DEMO OFF
: Display demonstration will be activated automatically if
no operation is done for about 20 seconds.
: Cancels.
CLOCK
CLOCK SET [ 1:00 ] : Adjust the hour, then the minute.
PRO EQ
BASS — : For settings, see “Storing your own sound mode” on
page 2.
MIDDLE
TREBLE
DISPLAY
DIMMER • DIMMER ON
• DIMMER OFF : Dims the display and button illumination.
: Cancels.
SCROLL * 1 • SCROLL ONCE
• SCROLL AUTO
• SCROLL OFF : Scrolls the displayed information once.
: Repeats scrolling (at 5-second intervals).
: Cancels.
Pressing DISP for more than one second can scroll the display regardless of
the setting.
TAG DISPLAY • TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA
tracks.
: Cancels.
TUNER
SSM * 2 • SSM 01 – 06
• SSM 07 – 12
• SSM 13 – 18 : For settings, see page 2.
MONO * 2 • MONO ON
• MONO OFF
: Activate monaural mode to improve FM reception, but
stereo effect will be lost. (See page 2.)
: Restore the stereo effect.
IF BAND • AUTO
• WIDE
: Increases the tuner selectivity to reduce interference
noises between adjacent stations. (Stereo effect may be
lost.)
: Subject to interference noises from adjacent stations,
but sound quality will not be degraded and the stereo
effect will remain.
COLOR
BUTTON ZONE COLOR 01 —
COLOR 29, USER : For settings, see the right column.
DISP ZONE
Display zone
ALL ZONE
COLOR SETUP
DAY COLOR • BUTTON ZONE
• DISP ZONE : For settings, see the right column.
NIGHT COLOR
MENU COLOR • ON
• OFF
: Changes the display and buttons (except for EQ/BASS-TRE
/ DISP) illumination during menu, list search and
playback mode operations.
: Cancels.
AUDIO
FADER * 3 R06 – F06 [ 00 ] : Adjust the front and rear speaker output balance.
BALANCE * 4 L06 – R06 [ 00 ] : Adjust the left and right speaker output balance.
LOUD • LOUD ON
• LOUD OFF
: Boost low and high frequencies to produce a well-
balanced sound at a low volume level.
: Cancels.
VOL ADJUST VOL ADJ –05 —
VOL ADJ +05
[ VOL ADJ 00 ] : Preset the volume adjustment level of each source
(except FM), compared to the FM volume level. The
volume level will automatically increase or decrease
when you change the source.
• Before making an adjustment, select the source you
want to adjust.
• “VOL ADJ FIX” appears on the display if “FM” is selected
as the source.
L/O MODE • SUB.W
• REAR
: Select if the REAR LINE OUT terminals are used for
connecting a subwoofer (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for
connecting the speakers (through an external amplifier).
SUB.W FREQ * 5 • LOW
• MID
• HIGH
: Frequencies lower than 72 Hz are sent to the subwoofer.
: Frequencies lower than 111 Hz are sent to the
subwoofer.
: Frequencies lower than 157 Hz are sent to the
subwoofer.
SUB.W LEVEL * 5 SUB.W 00 —
SUB.W 08 : Adjust the subwoofer output level.
[ SUB.W 04 ]
BEEP • BEEP ON
• BEEP OFF : Activates the keypress tone.
: Deactivates the keypress tone.
AMP GAIN * 6 • LOW POWER
• HIGH POWER
: VOLUME 00 – VOLUME 30 (Select if the maximum power
of each speaker is less than 50 W to prevent damaging
the speakers.)
: VOLUME 00 – VOLUME 50
SRC
SELECT
AM * 7 • AM ON
• AM OFF : Enable “AM” in source selection.
: Disable “AM” in source selection.
AUX IN * 8 • AUX ON
• AUX OFF : Enable “AUX IN” in source selection.
: Disable “AUX IN” in source selection.
* 1 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
* 2 Displayed only when the source is “FM.”
* 3 If you are using a two-speaker system, set the fader level to “00.”
* 4 This adjustment will not affect the subwoofer output.
* 5 Displayed only when is set to .
* 6 The volume level automatically changes to “VOLUME 30” if you change to with the volume level
is set higher than “VOLUME 30.”
* 7 Displayed only when any source other than “AM” is selected.
* 8 Displayed only when any source other than “AUX IN” is selected.
Menu operations
[Hold]
Selecting the variable buttons and display color illumination
You can select your preferred color for buttons illumination (except for EQ/BASS-TRE / DISP) and display color
separately.
1
or
2
] ] / ZONE> /
• Pressing COLOR in step 1 will enter zone selection menu (BUTTON ZONE /DISP ZONE
/ ALL ZONE) directly.3] Select your preferred color from one of the
29 preset colors or color.Button zoneAll zoneDisplay zone[Hold]4Repeat steps 2 and 3 to select a different zone
and your preferred color.
• If is selected in step 2, the buttons and display illumination changed
to the current/selected
color. You can also change the color to one of your preferred color by performing
step 3.5or] Exit from the setting.1or2] ] ]
• Pressing COLOR in step 1 will enter zone selection menu (BUTTON ZONE / DISP
ZONE) directly.3] Select a primary color.
RED j GREEN j BLUE j (back to the beginning)[Hold]4] Adjust the level of the selected primary
color.
00 to 315Repeat steps 3 and 4 to adjust other primary
colors.6or] Exit from the setting.If “00” is selected for all the primary colors (as in step
4) for , nothing appear on the display.Creating your own day and night colors—USERYou can create your own colors for and to apply to button zone and display
zone.
• Displayed when is set to .• Displayed when is set to .Menu hierarchyOperationCOLOR
SETUPDAY COLOR• BUTTON ZONEFollow example below.• DISP ZONEPress BACK after step 5, then select DISP ZONE in step 2.NIGHT COLOR• BUTTON ZONEPress BACK after step 5, then select NIGHT COLOR in step 2.• DISP ZONEEx.: Creating color for in .[Hold]EN_KD-R514[UI]_1.indd 3EN_KD-R514[UI]_1.indd 311/30/09 10:51:17 AM11/30/09 10:51:17 AM
selection menu (BUTTON ZONE /DISP ZONE
/ ALL ZONE) directly.
3
] Select your preferred color from one of the
29 preset colors or color.
Button zone
All zone
Display zone
[Hold]
4 Repeat steps 2 and 3 to select a different zone
and your preferred color.
• If is selected in step 2, the
buttons and display illumination changed
to the current/selected
You can also change the color
to one of your preferred color by performing
step 3.
5
or
] Exit from the setting.
1
or
2
] ] ]
selection menu (BUTTON ZONE / DISP
ZONE) directly.
3
] Select a primary color.
RED
j GREEN j BLUE j (back to the
beginning)
[Hold]
4
] Adjust the level of the selected primary
color.
00 to 31
5 Repeat steps 3 and 4 to adjust other primary
colors.
6
or
] Exit from the setting.
If “00” is selected for all the primary colors (as in step
4) for , nothing appear on the display.
Creating your own day and night colors—USER
You can create your own colors for and to apply to button zone and display
zone.
•
Displayed when is set to .
• Displayed when is set to .
Menu hierarchy Operation
COLOR
SETUP
DAY COLOR
• BUTTON ZONE Follow example below.
• DISP ZONE Press BACK after step 5, then select DISP ZONE in step 2.
NIGHT COLOR
• BUTTON ZONE Press BACK after step 5, then select NIGHT COLOR in step 2.
• DISP ZONE
Ex.: Creating color for
[Hold]
EN_KD-R514[UI]_1.indd 3 EN_KD-R514[UI]_1.indd 3 11/30/09 10:51:17 AM 11/30/09 10:51:17 AM