JVC DR-MV2SEU - Manual (Page 32)

32
Reco
rdin
g
EN
5
Select the recording media (“DVD”
or “VCR”) using [Cursor
U / D], then
press [Cursor P].
6 Select a recording speed using
[Cursor
U / D], then press
[Cursor P].
7 Select VPS / PDC “ON” or “OFF”
using [Cursor
U / D], then press
[ENTER]. (See page 31.)
8 Press [SET UP] or
[the SHOWVIEW button] to exit.
9
Press [TIMER ].
The icon will appear on the front panel display
and the unit enters to the timer-standby mode.
Note
• If you have not set the clock, the clock setting
window will appear after step 1. Continue from step
5 in “Manual Clock Setting” before programming the
timer. (See page 22.)
• If the S HOW V IEW programming number is not
available, “Code Error” is displayed and the number
will clear when you press [ENTER] in step 2.
• If the S HOW V IEW programming number previously
set overlaps with the one you entered and the
channel is different, “Overlap” is displayed but the
timer programming will be cleared when you press
[ENTER] in step 3.
• If you enter the same S HOW V IEW programming
number and the recording pattern which you have
already entered, the previously set programme will
be overwritten.
• If you enter the same S HOW V IEW programming
number but a different recording pattern, it will be
saved as a new programme and added to the timer
programming list.
“Code Error” is displayed if:
• A past time is entered for start and end times.
• The S
HOW V IEW programming number cannot be
decoded.
“Overlap” is displayed if:
• There is an overlap with a timer recording
setting in different channels.
Hints for Timer Recording
• If there is a power failure or the unit is unplugged for
more than 30 seconds, the clock setting and all
timer settings will be lost.
• If there is no disc or an unrecordable disc in the tray,
the DVD indicator on the front panel display will
flash and timer recording will not occur. Insert a
recordable disc.
• If there is no tape or a tape with a record tab is not in
the cassette compartment, the VCR indicator on the
front panel display flashes and timer recording
cannot be performed. Please insert a recordable
tape.
• When all timer recordings are complete, the
icon flashes. To play back or eject the recorded disc,
press [TIMER ], and then press [PLAY
P] or
[OPEN/CLOSE/EJECT O].
• The timer recording cannot be performed in DVD
and VCR at the same time. If you set two
programmings with the same channel and time both
in DVD and VCR, the programming that has priority
will be recorded.
• You cannot make any DVD operation during DVD
timer recording.
• You cannot make any VCR operation during VCR
timer recording.
• If the Start and End times are same, the length of
the recording will be set for 24 hours. If the disc
becomes full during recording, the unit will turn itself
off. To continue recording, press [TIMER ] to
cancel the timer-standby mode, insert a recordable
disc and press [TIMER ] again.
• If two or more programmes overlap, “Overlap” and
the overlapped programme number will appear on
the display.
• If the Start time is earlier and the End time is later
than the current time, the recording will start
immediately after you press [TIMER ].
• If a videotape ends during timer recording, the unit
will automatically stop, eject the videotape, and turn
itself off. To continue recording, insert a recordable
tape.
Priority of overlapped settings
The unit records programmes according to priority if
timer programmes overlap.
If the starting time is same:
• The timer programming set first (PROG. 1) has
priority.
PROG. 1
PROG. 2
PROG. 1 PROG. 2
PROG. 2
recording
will start
after
PROG. 1
recording is
completed.
Actual
recording
Additional 30 seconds (at the most) are cut off.
E9770ED_EN.book Page 32 Wednesday, August 3, 2005 6:35 PM