JVC DR-MV2SEU - Manual (Page 30)

30
Reco
rdin
g
EN
• Cancel the timer-standby mode by pressing
[TIMER ] before operation for either DVD or
VCR. When finished operating, press [TIMER ]
to resume the timer-standby mode.
If VPS / PDC is “ON”:
• In the timer-standby mode, you can neither turn on
the power nor use the component (VCR or DVD)
which is not currently timer-programmed.
If VPS / PDC is “OFF”:
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which
is not currently timer-programmed.
Checking, Cancelling, or Correcting
the Timer Programming Information
In the following example, No. 5 timer programming
overlaps on No. 1 and No. 6 timer programmes. In
such a case, you should correct the programme time
to clear the overlap.
1 Press [TIMER ] so that the icon
disappears from the front panel
display.
2
Press [PROG] twice.
Timer programming list will appear.
3
Check the information on the list you
will need.
4 To clear the timer programming,
select the desired programme using
[Cursor
U / D], then press [CLEAR].
To correct the timer programming
1) Select the desired programme using
[Cursor U / D], then press [ENTER].
2) Correct the timer programming using
[Cursor U / D / L / P].
3) Press [ENTER] again.
5
Press [PROG] to exit.
6 Press [TIMER ] to return to the
timer-standby mode.
To check the timer programming in progress
Press [PROG].
Note
• If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select
any other programmes.
• When you check the timer programming in progress
by pressing [PROG] during operations of the
component (DVD or VCR) which is not currently
used for the timer recording, the programme will not
be highlighted. In this case, you cannot select other
programmings.
To Stop the Timer Recording in
Progress
On the front panel of the unit, press
[DVD STOP
S] to stop the disc
recording or [VCR STOP/EJECT S/O] to
stop the tape recording.
Note
• [STOP S] on the remote control is not effective.
If the Timer Programming Did Not
Complete Correctly
The error number appears on the timer programming
list.
The error programme will be displayed in grey
with an asterisk and have an error number.
The error numbers indicate:
E1–E22, E37–E39: Recording error
E23–E24: Unrecordable disc
E25:•Copy prohibited programme
•Cannot record because of the NTSC / PAL-
60 signal is received.
E26–E28: Copy prohibited programme
E29: Disc protected
E30: Disc full
E31: Already recorded 99 titles (Video mode)
E32: Already recorded 99 titles (VR mode)
E33: Already recorded 999 chapters
E34: No space for Control Information
E35: PCA (Power Calibration Area) full
E36: Already finalised Video format disc
E40:•There are some unrecorded parts due the
overlapped timer programmes.
•Recording did not start at the start time.
•There is no tape in the cassette
compartment.
•Tape recording reaches to the tape end
during timer recording.
Timer Programming
1. 01/01 12:00 13:00 AV3 DVD XP ON
2. - - -
3. - - -
4. - - -
6. 01/01 13:45 21:00 P12 DVD SEP
7. - - -
8. - - -
Overlap
No.1 6
Date Start End CH Speed VPS
PDC
DVD
VCR
VCR DVD
5. 01/01 12:30 14:00 P02 VCR SP OFF
OFF
Timer Programming
Date Start End CH Speed
1.
2.
3.
4.
5.
6.
7.
8.
Timer Programming
Date Start End CH Speed
1.
2.
3.
4.
5.
6.
7.
8.
Timer Programming
01/01 12:00 13:00 AV3 DVD E1 ON
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
- - -
Date Start End CH Speed DVD
VCR
VCR DVD
2.
VPS
PDC
E9770ED_EN.book Page 30 Wednesday, August 3, 2005 6:35 PM