JVC GR-D22 User Manual
Page 23
EN
23
USING MENUS FOR DETAILED ADJUSTMENT
SYSTEM
“
SYSTEM” functions which are set when the Power
Switch
r
is set to “
” are also applied when the
Power Switch
r
is set to “PLAY” (
੬
pg. 24).
BEEP
OFF: Even though not heard while shooting, shutter
sound is recorded on the tape.
BEEP: The beep sounds when the power is turned on
or off, and at the beginning and end of recording. Also
to activate the shutter sound effect (
੬
pg. 18).
[MELODY]: Instead of a beep, a melody sounds
when any operation is performed. It also activates the
shutter sound effect (
੬
pg. 18).
TALLY
OFF: The tally lamp remains off at all times.
[ON]: The tally lamp comes on to signal the start of
recording.
REMOTE
It is recommended that this function be set to “OFF”
to prevent improper operation.
DEMO MODE
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as
Program AE with special effects, etc., and can be
used to confirm how these functions operate.
Demonstration starts in the following cases:
• When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
• With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch
r
is set to “
” or “
” .
Performing any operation during the demonstration
stops the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
● If a tape is in the camcorder, the demonstration cannot be
turned on.
● “DEMO MODE” remains “ON” even if the camcorder
power is turned off.
● If “DEMO MODE” remains “ON”, some functions will not
be available. After viewing demo, set to “OFF”.
PRIORITY
[LCD]: When the LCD monitor is fully open, even if
the viewfinder is pulled out, the image is displayed
only on the LCD monitor; it will not be displayed in the
viewfinder.
FINDER: When the viewfinder is pulled out, even if
the LCD monitor is fully open, the image is displayed
only in the viewfinder; it will not be displayed on the
LCD monitor.
CAM RESET
[RETURN]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-preset.
CAMERA DISPLAY
• Settings made in the “
CAMERA DISPLAY” Menu
are effective only for video shooting.
• Settings made in the “
CAMERA DISPLAY” Menu
remain effective even when the Power Switch
r
is
set to “
”. However, the menu settings can be
changed only when the Power Switch
r
is set to
“
”.
BRIGHT
੬
pg. 11, “To Adjust The Brightness Of The Display”
ON SCREEN
LCD: Keeps the camcorder’s display (except the
date, time and time code) from appearing on the
connected TV screen.
[LCD/TV]: Makes the camcorder’s display appear on
screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5
seconds in the following cases:
• When the Power Switch
r
is set from “OFF
(CHARGE)” to “
” or “
”.
• When tape playback starts. The camcorder displays
the date/time when scenes are recorded.
• When the date is changed during tape playback.
ON: The date/time is always displayed.
[ ] = Factory-preset
MELODY
EEP
B
–
RETURN
AM RESET
C
LCD
R I OR I TY
P
–
ON
EMO MODE
D
–
ON
EMOTE
R
–
ON
AL LY
T
–
S
Y
S
TEM
RETURN
–
–
–
A
R
E
M
A
C
D I SPLAY
RE N
E
ON SC
LCD / TV
U
A
O
T
I ME
T
DATE /
T I ME CODE
CLOCK
ADJ .
F F
O
25 ’03
C
E
D
30 PM
:
5
BR I GHT
GR-D22_16-28_EN
25/9/03, 3:31 PM
23