Manual timer programming, Arelief recordingb (a pg. 46). t, K has stopped. (a pg. 46 – JVC ShowView LPT1100-001A User Manual

Page 46: Arelief recordingb), Timer recording on hdd/dvd deck

Filename [DX5SEU_10Timer Recording.fm]

Masterpage:Left+

TIMER RECORDING ON HDD/DVD DECK

Page 46Thursday, 1 September 2005 13:26

You can programme this unit to timer record as many as 16
programmes.
If you do not know the S

HOW

IEW

number for the programme you

wish to record, use the following procedure to set your unit to timer
record the programme.

Load a recordable disc if recording to DVD.

Press PROGRAMME to access the programme top screen.

Press selection keys to select

ACALENDAR PR.B, then press

ENTER.

●

When

APROGRAMME FULL DELETE UNWANTED TIMER

PROGRAMMES

B appears on the TV screen, you need to

cancel some of the reserved programmes. (A pg. 47)

Press selection keys to select the desired date, then press
ENTER.

Press selection keys to select
ARECORD TOB, then press
ENTER. Press selection keys
to select the desired recording
deck, then press ENTER.

Press selection keys to select
ASTARTB, then press ENTER.
Press selection keys to set
the desired start time, then
press ENTER.

●

Each press of

F G increases/decreases the start time in 1-

minute intervals.

●

To increase/decrease the start time in 30-minute intervals,
press and hold

F G.

Press selection keys to select

ASTOPB, then press ENTER.

Press selection keys to set the desired stop time, then press
ENTER.

●

Each press of

F G increases/decreases the stop time in 1-

minute intervals.

●

To increase/decrease the stop time in 30-minute intervals,
press and hold

F G.

Press selection keys to select

ATV PROGB, then press ENTER.

Press selection keys to select the desired channel.

Press selection keys to select

ACONFIRMB, then press

ENTER.

Set the other recording options as required.

●

Refer to step 8 in

Press selection keys to
select

AOKB, then press

ENTER to access the
Programme Confirmation
screen.

Press selection keys to
select

AEXITB, then press

ENTER to complete timer
programming.

●

To programme another timer, press selection keys to select
ACONTINUEB, then press ENTER.

●

APROGRAMME OVERLAPPEDB appears on the TV screen,

delete or modify the programmes.

NOTES:

●

When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.

●

If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.

Manual Timer Programming

●

Make sure that the unit’s built-in clock is set properly.

●

Turn on the unit.

●

Turn on the TV and select the AV mode.

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

FGDE

PROGRAMME

ENTER

CABLE/SAT

DVD

Selection Keys

BBC1

[MISC. ] XP

BBC1

23:00

22:30

HDD

PROGRAMME > CALENDAR PR. (2/3)

CONFIRM

14/01/04 WED 22:30 - 23:00

RECORD TO

STOP

START

TV PROG

ENTER

SELECT

PROGRAMME

EXIT

PRESS [PROGRAMME]
TO EXIT

SELECT WITH @
THEN PRESS [ENTER]

Satellite Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB on this page.

In step 8, set

ATV PROGB to AL-2B.

B Set the satellite receiver to the appropriate channel before

the selected programme begins.

C Leave the satellite receiver’s power on.

Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in the recording mode as set.

●

If the remaining capacity of the hard disk is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.

●

AJUSTB is selected for the recording mode, the current

recording mode for the DVD deck is applied.

BBC1

1:00

28:00

ENTER

SELECT

PROGRAMME

EXIT

PROGRAMME > CALENDAR PR. (3/3)

PRESS [PROGRAMME]
TO EXIT

SELECT WITH @
THEN PRESS [ENTER]

INPUT TITLE