Vm9022hd satellite radio operation – Jensen VM9022HD User Manual

Page 25

VM9022HD

SATELLITE RADIO OPERATION

Listeners can subscribe to XM® Radio on the Web by
visiting www.xmradio.com, or by calling (800) 967-2346.
Customers should have their Radio ID ready (see
“Displaying the Identification (ID) Code”). Customers can
receive a limited number of free-to-air channels without
activation.

Accessing Satellite Radio Mode

Press the SRC button (8) on the front panel or remote control
(8) to switch to the SAT source.

SAT channel name

SAT channel number

SAT band

Time

Song title

Artist name

Song category

Signal strength indicator

Current preset channels/on-screen preset buttons

10. CH -: Select the previous channel
11.

CH +: Select the next channel

12. CAT +: Select next channel in current category only
13. CAT -: Select previous channel in current category only
14. Touch to enter channel directly using keypad on screen
15. CG: Access Channel/Category Guide mode
16. BAND: Change between SAT1, SAT2 and SAT3 bands
17. Touch to view the SETUP menu
18. Touch this area to view the SOURCE MENU and select

a new playback source

19. MEM: View screen used to enter current channel into

preset memory

20. DIAG: This feature is reserved for use by service

professionals for troubleshooting.

Displaying the Identification (ID)

Code

Before you listen to satellite radio, you must subscribe to the
service using your radio’s identification number. To display
the radio ID, press the left/right buttons (16, 17) on the
joystick or the CH - or CH + buttons on the touch screen
repeatedly to tune to channel “000”. The screen displays the
radio ID where the channel name is usually displayed.

Selecting a Station

Use the left/right joystick buttons or the CH - or CH + buttons
on the touch screen to change to another station.

Preset Mode

To enter preset mode, touch the BAND button on the screen,
or press the BAND button on the unit (14) or remote control
(20) to change between the following bands: SAT1, SAT2, or
SAT3 (indicated in the top left corner of the TFT screen).

Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the TFT screen.

Storing a Station
1.

Select a band (if needed), then select a station.

Touch the on-screen MEM button (18) to open the
preset screen.

Touch the preset number in which you would like to
store the current station (or press EXIT to cancel and
close the menu). The preset number and station
appears highlighted.

Recalling a Station
1.

Select a band (if needed).

Touch an on-screen preset button to select the
corresponding stored station.

Direct Tuning

To enter a radio station directly, touch the

button or

press the GOTO button (21) on the remote control to display
the direct entry menu.

Enter the desired radio station using the on-screen number
pad. Touch the Enter button to tune to the selected station.
To exit the screen without changing the station, touch Exit. To
clear your entry and start over, touch Clear.

Channel/Category Guide Mode

There are two search modes to help navigate through
channels and or categories. To access the Channel/Category
Guide mode, press the Enter (joystick) button (18) on the
remote control or the CG button on the touch screen.

Channel Guide is the default search mode. To access
Category Guide, press the TITLE button (2) on the remote
control or touch CAT on the touch screen. To return to
Channel Guide, touch CH on the screen or press the
SUBTITLE button (9) on the remote control.

Channel Guide Mode

When Channel Guide mode is selected, the first six satellite
channels are displayed in the boxes in the bottom left of the
TFT screen and the on-screen menu changes to facilitate
search mode.

SAT

SAT1

CH001

01:02

BAND

MEM

DIAG

XM Preview

Title: Fridays XM144!

XM Preview

Preview

CAT

Mem:

E x i t

P1 P2

P4 P5 P6

CH NO: _ _ _ /255

Clear

Exit