JAI M4+ CL - Manual (Page 25)

CV-M4 + /M4 + CL, CV-M7 + /M7 + CL
- 24 -
7.5. CV-M4 + command list
Command Name Format Parameter Remarks
A – General settings and useful commands
EB Echo Back EB=[Param.] 0=Echo off 1=Echo on Off at power up
ST Camera Status request ST? Actual setting
HP Online Help request HP? Command list
VN Firmware version VN? 3 letter version
B – Timing and shutter related commands
SC Scanning format
SC=[Param.] 0=full frame
2=1/4 partial
1=1/2 partial
3=1/8 partial
*1)
TR Trigger mode TR=[Param.] 0=normal
2=Pulse width
1=Edge
3=Frame delay
HC H synchronous accum HC=[Param.] 0=H synchr 1= H a-synchr
SM Shutter mode SM=[Param.] 0=Normal 1=Programmab.
SH Shutter speed SH=[Param.] 0=Off (1/24)
2=1/100
4=1/400
6=1/1500
8=1/5500
1=1/50
3=1/200
5=1/800
7=1/3000
9=1/10,000
All10 steps are
valid in normal
trigger mode.
PE Programmable expos. PE=[Param.] 0=2.5 H, 1=3.5H 1055=1057.5 H H= 39.3 µsec
Bin. H= 43.3 µsec.
BI Binning BI=[Param.] 0=off 1=vertical *1). Only for SC=0.
M4
+ and M4 + CL
SL Smearless SL=[Param.] 0=Off 1=ON TR=1, 2 or 3
RC Reset Continuous Trig RC=[Param.] 0=Off 1=ON Only for TR=1
C – Signals and polarity
SO Sync on video
SO=[Param.] 0=no sync on v. 1=sync on v. Pin #4 on 12 pin
ML MuLtiple shutter ML=[Param.] 0=OFF 1=On Multi Trig input
TR=3
SE Sync/EEN SE=[Param.] 0= Sync out 1=EEN out Pin #9 on 12 pin
FP FEN/LEN/EEN polarity FP=[Param.] 0= active low 1= active high
TP Trigger polarity TP=[Param.] 0= active low 1= active high *2)
TI Trigger Input TI=[Param.] 0= Hirose 12p 1= LVDS (CL)
D – Gain and analogue signals setting
GA Manual gain Level
GA=[Param.] 0=low 510=high Range 0 to 510
RP Rear Potentiometer RP=[Param.] 0=manual gain 1=rear potm.
SU Setup Level SU=[Param.] 0=low 255=high Range 0 to 255
E – Saving and loading data in EEPROM
LD Load settings from
camera EEPROM
LD=[Param.] 0=Factory data
2=User 2 area
1=User 1 area
3=User 3 area Latest used data
area becomes
default at next
power up
SA Save settings to
camera EEPROM
SA=[Param.] 1=User 1 area
3=User 3 area
2=User 2 area Parameter = 0 is
not allowed
EA EEPROM area request EA? 0=Factory data
3=User 3 area 1=User 1 area
3=User 3 area Return the used
data from area
*3)
*1)
Binning can also be selected by the internal switch SW301.6. Binning has priority over partial scanning. If partial scanning
is active when a binning mode is activated, binning will take over and the scanning will be full. The line frequency will be
lower in V binning modes (H= 43.3 µsec.).
*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.
*3) Data from the latest used data area is loaded as default on power up.
!! Do not try to use commands not shown in the list.