Troubleshooting 35, English – Motorola MDV560VR User Manual
Page 35
English
Troubleshooting 35
Symptom
No power.
The power is on, but the
DVD+VCR does not
work.
No picture.
No sound.
The playback picture is
poor.
The DVD+VCR does not
start playback.
The remote control does
not work properly.
Cause
"
"
The power cord is disconnected.
"
"
No disc is inserted.
"
"
No tape is inserted.
"
"
The TV is not set to receive DVD+VCR
signal output.
"
"
TV/VCR mode for DVD+VCR is set to
TV.
"
"
The video cable is not connected securely.
"
"
The connected TV power is turned off.
"
"
The equipment connected with the audio
cable is not set to receive DVD+VCR sig-
nal output.
"
"
The audio cables are not connected
securely.
"
"
The power of the equipment connected
with the audio cable is turned off.
"
"
The Digital Audio Output is set to the
wrong position.
"
"
The disc is dirty.
"
"
Tape heads are dirty.
"
"
Tape is a rental or was recorded on
another VCR.
"
"
No disc is inserted.
"
"
No tape is inserted.
"
"
An unplayable disc is inserted.
"
"
The disc is placed upside down.
"
"
The disc is not placed within the guide.
"
"
The disc is dirty.
"
"
The Rating level is set.
"
"
The remote control does not work.
"
"
The remote control is too far from the
DVD+VCR.
"
"
There is an obstacle in the path of the
remote control and the DVD+VCR.
"
"
The batteries in the remote control are
exhausted.
"
"
This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
Correction
"
"
Plug the power cord into the wall outlet
securely.
"
"
Insert a disc or tape. (Check that the disc
or tape indicator in the display
window is lit.)
"
"
Select correct video input mode on the TV
so the picture from the DVD+VCR
appears on the TV screen.
"
"
Press the TV/VCR button on the remote
control repeatedly to choose VCR mode.
TV indicator disappears in the display win-
dow.
"
"
Properly connect the video cable.
"
"
Turn on the TV.
"
"
Select the correct input mode of the audio
receiver so you can listen to the sound
from the DVD+VCR.
"
"
Properly connect the audio cable.
"
"
Turn on the equipment connected with
the audio cable.
"
"
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
"
"
Clean the disc.
"
"
Clean video heads.
"
"
Use
3/4
for manual tracking adjustment
while tape is playing.
"
"
Insert a disc or tape. (Check that the disc
or tape indicator in the display
window is lit.)
"
"
Insert a playable disc. (Check the disc type,
color system, and Regional code.)
"
"
Place the disc with the playback side down.
"
"
Place the disc on the disc tray correctly
inside the guide.
"
"
Clean the disc.
"
"
Cancel the Rating function or change the
rating level.
"
"
Point the remote control at the remote
sensor of the DVD+VCR.
"
"
Operate the remote control within 23 ft
(7 m).
"
"
Remove the items that could block signal.
"
"
Replace the batteries with new ones.
"
"
When using a VCR, first press the VCR
button. When using a DVD, first press the
DVD button.
Check the following guide for the possible cause of a problem before contacting service.