GE r10279v - Manual (Page 3)

Design Guide
THE INSTALLATION SPACE
The cutout depth should be 24 ″
The cutout dimensions shown allow for a full door swing
and access to the pull-out racks when installed as a
built-in in standard 24
″ deep cabinets.
• The wine chiller, wine reserve and beverage center
can be installed freestanding.
• If installing between frameless cabinets, a 1/2 ″ wide
filler strip or side panel may be needed on hinge side.
The filler strip will act as a spacer between the case
and adjacent cabinet door swing. The width
of the opening must include the filler panels.
NOTE: The door should protrude 1
″ beyond the
surrounding cabinets. Custom framed models will
protrude 1-7/8
″ beyond surrounding cabinet doors.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical must
be located on rear wall as shown. NOTE: GFI (ground
fault interrupter) is not recommended.
PRODUCT CLEARANCES
The stainless steel wine chiller, wine reserve and beverage
center is factory set for a 110
° door swing. Models that accept
custom panels have a 95 ° door swing.
When installed in a corner:
• Allow 4
″ min. clearance on the hinge side for the 90° door
swing and to allow racks to slide out.
• Allow 10 ″ minimum clearance on the hinge side for a full
110 ° door swing. (Models ZDWI240WII and ZDBI240WII have
a 95
° door swing.)
NOTE: Custom handle clearances may vary, depending on
custom handle depth.
• The door swing is reversible on all models. If desired, change the
door swing before installation or before installing the custom frame
panel.
Choose the location:
• These products may be closed in on the top and three sides as long
as the front is unobstructed for air circulation and proper access to
the door.
• Do not install these products where the temperature will go below
55 °F (13°C) or above 90°F (32°C).
• Do not install where it will be subject to direct sunlight, heat or
moisture.
• These products are not designed to be stacked one over the other.
Black or Stainless Steel Toekick Options
• These products are shipped with a black toekick installed.
An optional stainless steel toekick is also supplied with each
product. For shipping purposes, the stainless steel toekick is
secured to the back of the unit.
ZTBSS1 Tubular Handle
ZTBSS1 Monogram stainless steel tubular handle is available for
models ZDWI240WII and ZDBI240WII.
3
90 ° Door Swing
SIDE-BY-SIDE INSTALLATIONS
Increase storage capacity by installing two Monogram
beverage centers, wine chillers or wine reserves together.
Or, for a complete refreshment center, install any two
of these units together.
• A side-by-side installation requires at least a 47-1/2
″
wide opening. No trim kits required.
• Products must operate from separate, properly
grounded receptacles.
10" Minimum
to Wall
110 °*
*95 ° Door Swing on Custom Frame Models
21-5/8"
23-5/8"
4" Minimum
to Wall
90
°
34-1/2"-35"
24"
47-1/2" Min.
1-1/2"
9"
10-1/2"
9"
10-1/2"
14"
15"
Locate
Outlet
23-3/4"
34-1/4"
Locate
Outlet
34-1/2"-35"
24"
23-3/4" Min.
9" Max.
10-1/2"
1-1/2"
23-3/4" Stainless Steel Models 23-3/4" Stainless Steel Models
24-1/8" Framed Models
to 34-3/4"
NOTE:
Handle
and handle
standoff depth
is 1-3/4
″