Document Outline

• MH14-BIMH14 Warranty.pdf
  • WARRANTY STATEMENT
    • A. WARRANTY PROVISIONS - FRYERS
    • B. WARRANTY PROVISIONS - FRYPOTS
    • C. WARRANTY PROVISIONS - HEATING ELEMENTS
    • D. WARRANTY PROVISIONS - COOKING COMPUTER
    • E. PARTS RETURN
    • F. WARRANTY EXCLUSIONS
• McD H14 Series Chapter 1.pdf
  • CHAPTER 1: INTRODUCTION
  • 1.1 General
    • 1.2 Safety Information
    • 1.3 Computer Information
  • 1.4 European Community (CE) Specific Information
    • 1.5 Shipping Damage Claim Procedure
      • 1.6 Service Information
• McD H14 Series Chapter 2.pdf
  • CHAPTER 2: INSTALLATION INSTRUCTIONS
  • 2.1 General
    • • • DANGER
    • 2.2 After Fryers Are Under The Fry Station Hood
  • 2.3 Power Requirements
    • • • DANGER
  • 2.4 Frypot Boil-Out
• McD H14 Series Chapter 3.pdf
  • WITH M100B™ COOKING COMPUTERS
  • 3.1 Equipment Setup and Shutdown Procedures
    • • Setup
    • Shutdown
  • 3.2 Introduction To The M-100B™ Cooking Computer
  • 3.3 M-100B™ Computer Operating Instructions
    • Viewing the Frypot Temperature (Actual or Setpoint)
  • 3.4 M-100B™ Computer Problem Condition Indicators
    • Open Drain Valve Indication
    • Low Temperature Indication
    • Probe Failure Indication
    • If the temperature probe fails, the display will flash PROBE FAILURE and an audible alarm will sound. To cancel the alarm, turn the computer OFF. In split-vat fryers, turn off the side in which the failure occurred. If a probe fails during the high-li
    • Recovery Out of Range (REC LOC)
  • 3.5 M-100B™ Computer Set-Up and Programming Instructions
    • • • • In the Setup Mode, the operator can:
  • 3.5.1 M-100B™ Computer Setup Mode
    • • • • • How to Change Computer Product/Temperature Displays
  • 3.5.2 M-100B™ Computer Programming Mode
    • • • How to Display “Use Time” Information
      • How to Display the Product Cycle Accumulator Information
      • How to Use the Filter Countdown Timer
• McD H14 Series Chapter 4.pdf
  • 4.1 Equipment Setup and Shutdown Procedures
    • • Setup
    • Shutdown
  • 4.2 Introduction to the Analog Controller
  • Analog Controller Operating Instructions
  • Analog Controller High-Limit Check
• McD H14 Series Chapter 5.pdf
  • CHAPTER 5: OPERATING THE BUILT-IN FILTRATION SYSTEM
  • 8.1 STEP-BY-STEP FILTRATION INSTRUCTIONS
    • • • WARNING: Do Not Use Filter Powder on Filter Pads
    • 8.2 CARE AND CLEANING OF YOUR FRYER AND FILTER SYSTEM
• McD H14 Series Chapter 6.pdf
  • 6.1 Preventive Maintenance
  • Troubleshooting
  • 6.2.1 Troubleshooting Fryers Equipped with M100B Computers
    • Fryer Off
    • Fryer Heating Oil
  • 6.2.3 Troubleshooting the Built-in Filtration System (BIH14 units only)
• McD H14 Series Chapter 7.pdf
  • Solidified shortening in the pan or filter lines,
  • Or
    • ORIGINAL VS REDESIGNED FP-III FILTRATION SYSTEM
• McD H14 Series Chapter 8.pdf
  • 8.1 Accessories
  • ITEM
    • • Filter Pack– 100 Sheets
  • ITEM