FUJITSU MAX3036RC - Manual (Page 88)

Index
IN-2 C141-E237
high-speed data transfer .................................. 1-2
I
indicating revision number at factory
shipment .................................................... 6-8
initial diagnosis at time of power-on .............. 5-4
initial seek operation check........................... 6-10
initial self-diagnostic....................................... 6-2
installation....................................................... 5-1
installation requirement .................................. 4-1
installation/removal/replacement.................... 5-2
interface connector.......................................... 4-9
interface error ................................................. 7-4
interface test.................................................... 6-4
internal test space............................................ 3-3
L
large capacity .................................................. 1-4
leak magnetic flux........................................... 4-6
limitation of bottom-mounting ....................... 4-4
limitation of side-mounting ............................ 4-4
logical data block addressing .......................... 3-8
low noise and low vibration............................ 1-4
low power consumption.................................. 1-4
M
maintenance information ................................ 6-5
maintenance level ........................................... 6-7
maintenance requirement................................ 6-6
microcode downloading.................................. 1-4
MODE SELECT/MODE SELECT
EXTENDED command............................. 5-5
model name and order number ....................... 2-1
mounting drive................................................ 5-3
mounting frame structure................................ 4-3
mounting orientations ..................................... 4-2
mounting procedure ........................................ 5-3
mounting requirement..................................... 4-1
mounting screw............................................... 4-3
MTBF ............................................................. 2-5
MTTR ............................................................. 2-6
multi-segment data buffer............................... 1-2
N
noise filter ....................................................... 4-8
note on handling drive .................................... 5-1
note on mounting ............................................ 4-3
O
online self-diagnostic...................................... 6-3
operation check............................................. 6-10
operation test................................................. 6-10
outline of troubleshooting procedure............ 6-11
P
packaging ........................................................ 5-2
PAD ................................................................ 3-7
page code = 1 .................................................. 5-8
page code = 3 .................................................. 5-5
page code = 7 .................................................. 5-8
page code = 21 ................................................ 5-8
part replacement.............................................. 6-7
part that can be replaced in field ..................... 6-6
physical sector allocation ................................ 3-5
PLO Sync........................................................ 3-7
port address ..................................................... 5-3
port addressing ................................................ 1-6
positioning error rate....................................... 2-5
power on/off sequence .................................... 4-7
power supply requirement .............................. 4-7
precaution ....................................................... 6-5
preventive maintenance .................................. 6-6
programmable data block length..................... 1-3
R
random/sequential read test............................. 6-4
read/write circuit ............................................. 1-5
read/write error recovery parameter................ 5-8
ready LED output signal ............................... 4-11
reliability ......................................................... 2-5
reporting result of self-diagnostic and
error indication .......................................... 6-3
reserve and release function............................ 1-3
responses to operation errors .......................... 5-4
restriction of use of hazardous substance........ 1-1
revision number .............................................. 6-7
S
SAS standard................................................... 1-2
sector format ................................................... 3-6
seek test........................................................... 6-2
self-diagnostic ................................................. 6-1
SEND DIAGNOSTIC command .................... 6-3
sense data ........................................................ 7-1
1-1x-xx .................................................... 7-4
3-0C-03 .................................................... 7-4
3-1x-xx .................................................... 7-4
4-32-01 .................................................... 7-4
4-40-xx .................................................... 7-4
4-44-xx .................................................... 7-4
4-C4-xx .................................................... 7-4
5-2x-xx .................................................... 7-4
B-44-xx .................................................... 7-4
B-47-xx .................................................... 7-4
B-4B-xx ................................................... 7-4
B-4E-00 ................................................... 7-4
E-1D-00 ................................................... 7-4
sense data analysis .......................................... 7-3