Altera Santa Cruz - Manual (Page 20)

2–14 Chapter 2: Board Components
MICTOR Connector (J2)
Santa Cruz, USB, MICTOR, SD Card HSMC Reference Manual © December 2008 Altera Corporation
To use this interface, you must configure the JTAG interface on the HSMC interface
host board. The following procedure shows you how to use the MICTOR interface
using the Cyclone III starter board as an example:
1. Connect the THDB-SUM board to the Cyclone III starter board.
2. Remove the jumpers, JP1 and JP2, of the Cyclone III starter board to connect the
JTAG interface between the Cyclone III FPGA and the THDB-SUM board.
3. Short the TDI and TDO pins of the JTAG connector (J4), as shown in Figure 2–12 .
8 MICTOR_D13 121 MICTOR_D13 HSMC_TX_N11
9 MICTOR_D23 128 MICTOR_D23 HSMC_RX_N12
10 MICTOR_D12 125 MICTOR_D12 HSMC_TX_P12
13 MICTOR_D22 126 MICTOR_D22 HSMC_RX_P12
16 MICTOR_D11 127 MICTOR_D11 HSMC_TX_N12
18 MICTOR_D10 131 MICTOR_D10 HSMC_TX_P13
20 MICTOR_D9 133 MICTOR_D9 HSMC_TX_N13
22 MICTOR_D8 137 MICTOR_D8 HSMC_TX_P14
23 MICTOR_D21 122 MICTOR_D21 HSMC_RX_N11
24 MICTOR_D7 139 MICTOR_D7 HSMC_TX_N14
25 MICTOR_D20 120 MICTOR_D20 HSMC_RX_P11
26 MICTOR_D6 119 MICTOR_D6 HSMC_TX_P11
27 MICTOR_D19 116 MICTOR_D19 HSMC_RX_N10
28 MICTOR_D5 109 MICTOR_D5 HSMC_TX_N9
29 MICTOR_D18 114 MICTOR_D18 HSMC_RX_P10
30 MICTOR_D4 107 MICTOR_D4 HSMC_TX_P9
31 MICTOR_D17 110 MICTOR_D17 HSMC_RX_N9
32 MICTOR_D3 115 MICTOR_D3 HSMC_TX_N10
33 MICTOR_D16 108 MICTOR_D16 HSMC_RX_P9
34 MICTOR_D2 113 MICTOR_D2 HSMC_TX_P10
35 MICTOR_D15 104 MICTOR_D15 HSMC_RX_N8
36 MICTOR_D1 103 MICTOR_D1 HSMC_TX_N8
37 MICTOR_D14 102 MICTOR_D14 HSMC_RX_P8
38 MICTOR_D0 101 MICTOR_D0 HSMC_TX_P8
11 MICTOR_TDO 37 HSMC_TDO HSMC_TDO
15 MICTOR_TCK 35 HSMC_TCK HSMC_TCK
17 MICTOR_TMS 36 HSMC_TMS HSMC_TMS
19 MICTOR_TDI 38 HSMC_TDI HSMC_TDI
Table 2–12. MICTOR Connector (J2) Pin Assignments (Part 2 of 2)
MICTOR Connector
Pin Number
MICTOR Connector
Signal Name HSMC Pin Number HSMC Signal Name HSMC Pin Name