Innotech Genesis V4 System - Manual (Page 69)

Installation Instructions for Innotech Genesis Systems
Edition 011100 4-14
Figure 4-5. AISC Locations.
When an Analogue Input Module LEM is used, the output of the LEM is connected to one
of the controller’s analogue input channels. Because the cable between the LEM and the
controller is very short, this connection is checked by visual inspection. When checking
the analogue connection between the AIM LEM and a controller, ensure the cable is wired
in accordance with Section 3 and is free of potential physical damage. Ensure, also, that
the cable is routed outside of the cable ducts.
NOTE
The wiring checks in the following paragraphs are performed with the
AISCs removed. The units are delivered with their AISCs removed.
Do not install the AISCs until all wiring checks are completed.
4-1.2.4.1. Voltage Checks. This paragraph contains procedures for checking
analogue inputs associated with AISC Models D05, D33, V05 and V10. Note from
Table 4-3 that inputs associated with Digital AISC D05 will be either Zero Volts OR
5Vdc but not between the two extremes. The same is true for AISC D33 except that the
voltage range is Zero OR 10Vdc.
Note also that inputs associated with AISC Models V05 (0 – 5Vdc) and V10 (0 –
10Vdc) may be at any value within the ranges noted.
1
2
3
J
I
H
G
F
E
D
C
B
A A
I5
A
I6
A
I7
A
I8
A
I9
+
+
+
+
+
-
-
-
-
-
SCREEN
DDC Terminal 35
Sensor #7
Innotech Temperature
Sensor #8
Innotech Temperature
Sensor #9
Innotech Temperature
Sensor #10
Innotech Temperature
Sensor #11
Innotech Temperature
Address
jumpers
A
0
A
1
A 1
< n o t u
s e d >
A
2
Local Expansion Module #1 (AI)
ANALOGUE INPUTS
SCREEN MUST
GO HERE!
9
0
9
1
9
2
9
3
8
9 +
C
+
-
-
G
lo
b
a
l
N
e
t
R
S
-4
8
5
3
7
3
8
3
9
4
0
+
+
-
-
1
2
V
P
C G
N
9
0
9
1
8
9 +
G
- 9
3
9
4
9
2 +
G
-
A
lt
e
rn
a
tiv
e
P
lu
g
S
ty
le
R
S
-4
8
5
R
S
-2
3
2
L
E
M
C
O
M
M
S
GENESIS II DDC INNOTECH
(Wiring diagram - bottom board)
3
6
3
5
3
4
3
3
3
2
3
1
3
0
2
9
2
8
2
7
2
6
2
5
2
4
2
3
2
2
2
1 A
I1
A
I2
A
I3
A
I4
A
I5
A
I6
A
I7
A
I8
+
+
+
+
+
+
+
+
-
-
-
-
-
-
-
-
2
0
1
9 S
C
R S
S
OUTPUTS
ANALOGUE
0 1
0 3
0 4
0 5
0 6
0
7
0 8
0 9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
7
6
7
5
7
4
7
3
6
8
6
7
6
6
6
5 1
3
2
4
9
1
2
1
1
1
0
8
8
8
7
8
6
8
5
8
0
7
9
7
8
7
7 5
7
6
8
1
3
1
6
1
5
1
4
8
4
7
2
7
1
7
0
6
9
8
3
8
2
8
1
Siren
SSR #3
VAV #3
VAV #4
SSR #4
SSR #1
VAV #1
VAV #2
SSR #2
SSR #5
VAV #5
Sensor #6
Innotech Temperture
Switchboard Temp
Thermistor, Philips 10k
AI LEM #1, Terminal 3
NC
Sensor #5
Innotech Temperture
Sensor #4
Innotech Temperture
Sensor #3
Innotech Temperture
Sensor #2
Innotech Temperture
Sensor #1
Innotech Temperture
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps
AIM:
TH7: Thermistor
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps
TD1: 0-250 µAmps TD1: 0-250 µAmps
TD1: 0-250 µAmps
ANALOGUE
INPUT
SIGNAL
CONDITIONERS