IBM Partner Pavilion T400F - Manual (Page 5)

Contents
Safety and Environmental Notices . . . . . . . . . . . . . . . . . vii
Danger Notice . . . . . . . . . . . . . . . . . . . . . . . . . vii
Caution Notice . . . . . . . . . . . . . . . . . . . . . . . . . vii
Attention Notice
. . . . . . . . . . . . . . . . . . . . . . . . viii
Laser Safety and Compliance . . . . . . . . . . . . . . . . . . . viii
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . ix
Related Publications . . . . . . . . . . . . . . . . . . . . . . . ix
IBM Ultrium Publications. . . . . . . . . . . . . . . . . . . . . ix
IBM Fibre Channel Publications . . . . . . . . . . . . . . . . . . ix
Other Publications . . . . . . . . . . . . . . . . . . . . . . . ix
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1
Cartridge Compatibility
. . . . . . . . . . . . . . . . . . . . . . 2
Speed Matching and Channel Calibration . . . . . . . . . . . . . . . 2
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Supported Servers and Operating Systems . . . . . . . . . . . . . . . 3
SCSI Attachment
. . . . . . . . . . . . . . . . . . . . . . . . 4
Physical Characteristics of the SCSI Interface . . . . . . . . . . . . . 4
Speed
. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Address Assignments . . . . . . . . . . . . . . . . . . . . . . 5
Installing, Removing, or Resetting a Drive on an Active SCSI Bus
. . . . . 5
Fibre Channel Attachment . . . . . . . . . . . . . . . . . . . . . 6
Supported Topologies . . . . . . . . . . . . . . . . . . . . . . 6
Speed
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Address Assignments . . . . . . . . . . . . . . . . . . . . . . 7
World Wide Names . . . . . . . . . . . . . . . . . . . . . . . 8
Physical Characteristics of the Fibre Channel Interface
. . . . . . . . . 8
Installing, Removing, or Resetting a Drive on an Active Fibre Channel . . . . 8
Supported Device Drivers . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2. Specifications . . . . . . . . . . . . . . . . . . . . 11
Chapter 3. Installing the Tape Drive . . . . . . . . . . . . . . . . 13
Rear View of the SCSI Drive . . . . . . . . . . . . . . . . . . . . 14
Rear View of the Fibre Channel Drive
. . . . . . . . . . . . . . . . 15
Step 1. Unpack the Drive . . . . . . . . . . . . . . . . . . . . . 16
Step 2. Remove Power from the Enclosure
. . . . . . . . . . . . . . 16
Step 3. Set the SCSI ID or Arbitrated Loop Physical Address . . . . . . . . 17
Setting the SCSI ID (SCSI Drive Only) . . . . . . . . . . . . . . . 17
Setting the Arbitrated Loop Physical Address (Fibre Channel Drive Only)
19
Step 4. Change the Link Services of the Drive (optional) . . . . . . . . . 24
Step 5. Mount the Tape Drive into the Enclosure . . . . . . . . . . . . 26
Step 6. Connect and Test Power to the Tape Drive. . . . . . . . . . . . 27
Step 7. Connect the Internal SCSI or Fibre Channel Cable. . . . . . . . . 27
Step 8. Connect the Internal LDI Cable (optional) . . . . . . . . . . . . 28
Step 9. Run Drive Diagnostics . . . . . . . . . . . . . . . . . . . 28
Step 10. Install the Device Drivers . . . . . . . . . . . . . . . . . . 28
Step 11. Connect the External SCSI or Fibre Channel Interface to the Server
28
Connect the External SCSI Interface to the Server . . . . . . . . . . . 28
Connect the External Fibre Channel Interface to the Server
. . . . . . . 29
Step 12. Connect the External LDI Interface to the Server (optional) . . . . . 29
© Copyright IBM Corp. 2002 iii