Marantz DLPTM VP-12S3/VP-12S3L - Manual (Page 7)

ENGLISH
1
There is potential glass particle hazard if the lamp ruptures.
There is a potential hazard of glass particle if the lamp ruptures.
In case of lamp rupture,contact your nearest Marantz Authorized Dealer or Service Center for a replacement.
See “Replacing Lamp Unit”. (
☞
P.34)
For minimal servicing and to maintain high image quality, avoid humidity,
dust and cigarette smoke.
When the projector is subjected to these environments,the lens and
part of ventilation holes must be cleaned more often than usual. As long
as the projector is properly maintained in this manner, use in these
environments will not reduce the overall operation life. Please note that
all internal cleaning must be performed by an Marantz Authorized
Dealer, or Service Center.
• Do not expose the projector to extreme heat or cold.
Operating temperature:41 °F to 95 °F (+5 °C to 35 °C)
Storage temperature:–4 °F to 140 °F (–20 °C to +60 °C)
• The exhaust ventilative hole, the lamp cage cover and adjacent
areas may get extremely hot during projector operation. To
prevent injury,do not touch these areas until they have sufficiently
cooled down.
• Allow at least 1 foot (30 cm)of space between the exhaust
ventilative hole and the nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will
automatically turn off the projector lamp. This does not indicate a
malfunction. Remove the projector power cord from the wall outlet
and wait at least 10 minutes.
Then turn on the power by plugging the power cord back in. This
will return the projector to the normal operating condition.
Notes on Operation
Caution Concerning the Setup of the
Projector
WARNING THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
MODEL NO. VP-16S1 / U1M AC 120V 60HZ 2.0A
SERIAL NO.
CAUTION : HIGH PRESSURE LAMP MAY EXPLODED IF IMPROPERLY HANDLED.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
CAUTION HOT : UNPLUG THE POWER CORD AND WAIT
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION CHAUD : DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
M MODEL NO. VP-12S1 / N1S
MADE IN JAPAN
FABRIQUE AU JAPON
AC 120V 60H Z 2.0W
SERIAL NO.
CAUTION :
HIGH PRESSURE LAMP
MAY EXPLODED IF IMPROPERLY HANDLED.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION :
LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
CAUTION HOT :
UNPLUG
THE POWER CORD AND WAIT
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
Caution Concerning the Lamp Unit
Caution Concerning the Lamp
Replacement
95˚F
(+35˚C)
41˚F
(+5˚C)
IMPORTANT SAFEGUARDS