Marantz DLPTM VP-12S3/VP-12S3L - Manual (Page 40)

ENGLISH
CAUTION:
• Do not touch the lamp and the lamp unit carelessly. It is
extremely hot. Wait at least one hour for the lamp to cool
down before handling.
• Do not loosen any screws except for those mentioned
below.
• The lamp may break if handled improperly.
• Do not use other than a Marantz replacement lamp unit.
❖
How to replace the Lamp Unit
PREPARATION:
When replacing the lamp, turn off the power for the
projector. After the cooling fan stops, disconnect the
power cord and wait for one hour until the lamp is cooled
down completely, then replace the lamp.
1. Press the STANDBY button on the remote controller or
the POWER button on the projector to turn the projector
off.
2. After the cooling fan stops, Unplug the AC power cord.
3. Wait at the least one hour for the lamp and lamp unit to
cool down.
4. Read the caution and warning labels on the unit.
PATT.
MENU V-MUTE
ENTER
PATTERN
STANDBY POWER ON
Replacing Lamp Unit
❖
Initialize the Lamp Life
The lamp has a lamp life of 2000 hours. The projector is
designed to shut OFF power if the lamp is used beyond this
2000 hours lamp life. In such case, replace the lamp and
reset the lamp life counter as follows.
1. After the message “Lamp Life 0 Hours” appears, power
to the projector shuts OFF. Promptly replace the lamp
with a new one. (
☞
P.34 “Replacing Lamp Unit”)
2. Once the lamp has been replaced, press the POWER
ON button on the remote control or the POWER button
on the projector.
The below message appears on the screen for 120 seconds.
3. Select “Yes”, using the
1 / 2
buttons.
4. Press the ENTER button. The lamp life indicator is now
initialized.
PATT.
MENU V-MUTE
ENTER
PATTERN
STANDBY POWER ON
2.
3.
4.
3.
2.
4.
Yes No
New Lamp ?
34
Lamp cover
WARNING THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
MODEL NO. VP-16S1 / U1M AC 120V 60HZ 2.0A
SERIAL NO.
CAUTION : HIGH PRESSURE LAMP
MAY EXPLODED IF IMPROPERLY HANDLED.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
CAUTION HOT : UNPLUG
THE POWER CORD AND WAIT
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
M MODEL NO. VP-12S1 / N1S
MADE IN JAPAN
FABRIQUE AU JAPON
AC 120V 60H Z 2.0W
SERIAL NO.
CAUTION : HIGH PRESSURE LAMP
MAY EXPLODED IF IMPROPERLY HANDLED.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
CAUTION HOT : UNPLUG
THE POWER CORD AND WAIT
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.