beautypg.com

Using the a ir conditioner controls, Remote control, Cool mode – GE 8,050 BTU Smart Window Air Conditioner Installation Instructions User Manual

Page 6

background image

6

49-5000433

Remote Control

Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW

the signal receiver on the air conditioner.

Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG

the remote control that could block the signal.

Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRIXSWR

20 feet.

Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\

as indicated on the remote control.

Ŷ5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWR

metal surfaces.

Cool Mode

8VHWKH&RROPRGHDW/RZ0HG+LJKRU$XWR)DQ
6SHHGIRUFRROLQJ8VHWKH7HPSHUDWXUH,QFUHDVH

Decrease

pads to set the desired temperature between

64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air will
become cooler. Set the thermostat at a higher number
and the indoor air will become warmer.

NOTE:

If the air conditioner is off and is then turned on

while set to a Cool setting or if turned from a fan setting
to a Cool setting, it may take approximately 3 minutes for
the compressor to start and cooling to begin.

Cooling Descriptions
For Normal Cooling—

Select the Cool mode and High

or Med fan with a middle set temperature.

For Maximum Cooling—

Select the Cool mode and

High fan with a lower set temperature.

For Quieter and Nighttime Cooling—

Select the Cool

mode and Low fan with a middle set temperature.

USING THE

A

IR CONDITIONER

Controls

Sleep Pad

The

SLEEP

mode sets the unit to gradually change

settings over an 8 hour period to allow for some
increased energy efficiency during sleep hours.
The

SLEEP

mode is available only in

COOL

and

FAN

only settings.

Press the

SLEEP

mode pad and its light will

illuminate. The fan indicator will stay at the same
setting but the air conditioner will automatically
change the

FAN

speed to low in either

COOL

or

FAN

only mode.

In

FAN

only mode, the fan will stay in the

LOW

speed setting for 8 hours. After 8 hours, the air
conditioner will resume the settings that were in
place before the

SLEEP

mode pad was pressed.

In

COOL

mode, the fan will stay in the

LOW

speed

setting for 8 hours from the time the

SLEEP

mode

pad was pressed. The air conditioner will also
raise the set point 2

°

F in 30 minutes and 2

°

F more

in another 30 minutes where it will remain for the
next 7 hours. After 8 hours, the air conditioner will
resume the settings that were in place before the

SLEEP

mode pad was pressed.

While the unit is in

SLEEP

mode, pressing any pad

will return it to the settings that were in place before
the

SLEEP

mode pad was pressed.

Control Display On and Off

To reduce brightness during sleeping hours, this
air conditioner control display has an automatic
off feature where the control display will turn off
completely after 5 minute of inactivity. To illuminate
the control interface, press any button on the
control display or remote control. The control
display will illuminate all previously illuminated
LED’s. The control interface will now respond to
any prescribed button press after it is illuminated.

Press and hold the FAN+MODE buttons

simultaneously to toggle this feature ON or OFF.
The LED’s will now stay ON anytime the unit is
ON.

Control Sound On and Off

This air conditioner will make a beep when
the buttons on the control are pushed or if the
unit receives a command from the mobile app
or remote control. To silence these beeps,
simultaneously press the FAN and “-” buttons for 3
seconds. Press these buttons again to toggle the
sound back on.