Envision Peripherals R-410A - Manual (Page 17)

17
ENVISION RESIDENTIAL INSTALLATION MANUAL
Setting Fan Speed - ECM
ECM2 fan motors have a 12-speed selector dip switch on the logic board (SW1) and are factory set for optimum perfor-
mance. To change speeds, select the appropriate speeds on dip switch SW1. Consult the ECM2 fan performance table
below for specific airflow and switch information.
CAUTION: Disconnect all power before performing this operation.
Fan Performance Data - ECM
ECM2
1
2
3
4
5
6
7
8
9
10
11
12
SW1
On Off
A 12-position DIP switch package on the control allows the airflow levels to be set for low, medium, and high
speed when using the ECM2 blower motor. Only three of the DIP switches can be in the "on" position.
The first "on" switch (the lowest position number) determines the low speed fan setting. •
The second "on" switch determines the medium speed fan setting. •
The third "on" switch determines the high speed fan setting. •
The example to the right shows SW1 on the control board configured for the following NS042 airflow settings.
Low Speed Fan: 900 CFM •
Medium Speed Fan: 1150 CFM •
High Speed Fan: 1450 CFM •
Single Speed
Dual Capacity
MAX AIR FLOW DIP SWITCH SETTINGS
ESP 1 2 3 4 5 6 7 8 9 10 11 12
400 500 600 700 800 900 1000 1100 1200
L M H
400 500 600 700 800 900 1000 1100 1200
L M H
650 750 850 1000 1100 1200 1300 1400 1500
L M H
036 800 1000 1100 1300 1500 1600 1800
w/1hp* L M H
650 800 900 1050 1150 1250 1350 1450 1550
L M H
042 800 900 1000 1200 1400 1600 1700 1850 2000 2200 2300 2400
w/1hp* L M H
650 800 900 1050 1150 1250 1350 1450 1550
L M H
048 800 900 1000 1200 1400 1600 1700 1850 2000 2200 2300 2400
w/1hp* L M H
800 950 1100 1300 1500 1750 1950 2100 2300
L M H
800 950 1100 1300 1500 1750 1950 2100 2300
L M H
5/30/06
Factory settings are at recommended L-M-H DIP switch locations CFM is controlled within ±5% up to the maximum ESP
M-H settings MUST be located within boldface CFM range Max ESP includes allowance for wet coil and standard filter
Lowest and Highest DIP switch settings are assumed to be L and H respectively
MAX AIR FLOW DIP SWITCH SETTINGS
ESP 1 2 3 4 5 6 7 8 9 10 11 12
400 500 600 700 800 900 1000 1100 1200
L M H
650 750 850 1000 1100 1200 1300 1400 1500
L M H
038 800 1000 1100 1300 1500 1600 1800
w/1hp* L M H
650 800 900 1050 1150 1250 1350 1450 1550
L M H
049 800 900 1000 1200 1400 1600 1700 1850 2000 2200 2300 2400
w/1hp* L M H
800 950 1100 1300 1500 1750 1950 2100 2300
L M H
800 950 1100 1300 1500 1750 1950 2100 2300
L M H
5/30/06
Factory settings are at recommended L-M-H DIP switch locations CFM is controlled within ±5% up to the maximum ESP
M-H settings MUST be located within boldface CFM range Max ESP includes allowance for wet coil and standard filter
Lowest and Highest DIP switch settings are assumed to be L and H respectively
MODEL
022 0.50
026 0.50
0.75
030 0.50
036 0.50
0.75
042 0.50
0.75
048 0.50
MODEL
070 0.75
060 0.75
049 0.50
0.75
038 0.50
0.75
072 0.75
064 0.75