Tascam ML-32D Dante / Analog Converter - Manual (Page 11)

TASCAM ML-32D / ML-16D
11
5
Latency setting
Set the latency.
Use the following guidelines to change the latency setting.
Selectable
latency value
Connected network setup guideline
250usec
The transmission route from the trans-
mitting device to the receiving device
passes through 1 gigabit switching hub.
500usec
The transmission route from the trans-
mitting device to the receiving device
passes through 5 gigabit switching hub.
1msec
The transmission route from the trans-
mitting device to the receiving device
passes through 10 gigabit switching hub.
2msec
The transmission speed of the transmit-
ting device is 100 Mbps.
5msec
Use this maximum selectable latency val-
ue when creating a large-scale network.
CAUTION
i Changing the name of a device will clear audio routing
settings. For this reason, we recommend changing device
names to names that are easy to identify before setting audio
routings.
i Depending on network connection conditions, setting the
latency to a value higher than the guideline might be neces-
sary.
NOTE
When using a switched (daisy chain) connection that does
not use a switching hub, set the latency according to the
number of Dante devices that signals pass through as shown
below.
Switched (daisy chain) connection example
Passes through 2 devices
Passes through 1 devices
Transmitting
device
Receiving
device
1st device 2nd device
Receiving
device
1st device
Transmitting
device
Specifications
Ratings
Formats
44.1/48 kHz, 16/24 bit
88.2/96 kHz, 16/24 bit
Input/output ratings
PRIMARY/SECONDARY connectors
Connector: RJ-45
Transmission protocol: Dante
Gigabit Ethernet standard: 1000BASE-T (IEEE 802.3ab)
Cables: category 5e or faster STP cables
ANALOG OUTPUTS connectors
Connector: D-sub 25-pin
Locking screws: No. 4-40 UNC (inch type)
Nominal output levels: +4 dBu, +6 dBu (only when maximum
output level is +15 dBu)
Maximum output levels: +24 dBu, +22 dBu, +20 dBu, +18
dBu, +15 dBu (set by REF. LEVEL
switches)
Output impedance: 200 Ω or lower
Applicable load impedance: 2 kΩ or higher
ANALOG INPUTS connectors
Connector: D-sub 25-pin
Locking screws: No. 4-40 UNC (inch type)
Nominal input levels: +4 dBu, +6 dBu (only when maximum
input level is +15 dBu)
Maximum input levels: +24 dBu, +22 dBu, +20 dBu, +18 dBu,
+15 dBu (set by REF. LEVEL switches)
Input impedance: 10 kΩ or higher
0
0 dBu=0.775 Vrms
Audio performance
0 ANALOG IN e DANTE OUT
Frequency response
+0.1 dB/-0.5 dB: 20 Hz/20 kHz
(-16 dBFS input, 44.1/48 kHz sampling frequency, JEITA)
+0.1 dB/-0.5 dB: 20 Hz/40 kHz
(-16 dBFS input, 88.2/96 kHz sampling frequency, JEITA)
Distortion (THD+N)
0.001% or less
(-1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency,
JEITA)
S/N ratio
113 dB or higher
(44.1/48/88.2/96 kHz sampling frequency, JEITA)
Crosstalk
115 dB or higher
(1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)