Wireless network connection further information – PLANET WNRT-633 User Manual

Page 2

Note

– 1 –

– 2 –

– 3 –

– 4 –

1. Package Contents

3. Hardware Installation

2. Physical Introduction

– 7 –

– 8 –

4. Wired Network Configuration (Windows 7)

5. Enter into the Web Management

– 5 –

– 6 –

Front Panel Description

Rear Panel Description

Wireless Router

Quick Guide

CD-ROM

Ethernet Cable

5dBi Antennas

The above steps introduce simple installations and configurations
of the WNRT-633. For further configurations of WAN, LAN,
Wireless, Firewall, Virtual Server, Security, Routing, DMZ, DDNS,
etc, please refer to the user’s manual in the CD. If you have further
questions, please contact the local dealer or distributor where you
purchased this product.

2011-E50300-000

Thank you for choosing PLANET WNRT-633. Before installing the

router, please verify the contents inside the package box.
The WNRT-633 should contain the following items in the package:

If there is any item missing or damaged, please

contact the seller immediately.

STEP 1: Locate the Wireless Router in an optimum place, and

adjust the antenna for the best coverage.

6. Wireless Network Connection

Further Information

STEP 1: Right-Click on the network icon displayed in the

system tray.

STEP 2: Connect the Power Adapter provided in the package

to the Wireless Router. The power LED (PWR) on the

front panel will turn on accordingly.

STEP 3: Follow the figure below to connect the network

devices. It depends on your network environment to

connect the WAN port to a Cable/xDSL modem, or the

Ethernet directly in your place.

A computer with wired Ethernet connection is required for the

first-time configuration of the Wireless Router.

Set your computer to get an IP address from the Wireless

Router:

1. Click “Start” button located at the lower-left corner of your

computer.

2. Click “Control Panel”.
3. Double click “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double click “Local Area Connection”.
6. Select “Internal Protocol Version 4(TCP/IPv4)” and

click “Properties”.

7. Select “Obtain an IP Address automatically” and

“Obtain DNS Server Address automatically”, and then

click “OK” button twice to save the configuration.

Default IP Address: 192.168.1.1

Default Username: admin

Default Password: admin

Default SSID: WNRT-633

Default Wireless Encryption Type: None

STEP 3: Enter the encryption key of the Wireless Router if

necessary.

STEP 1: The Web management allows you to access and

manage the Wireless Router easily. Launch the Web

browser and enter the default IP address

http://192.168.1.1

WNRT-633

Quick Installation Guide

300Mbps 802.11n Wireless

Gigabit Broadband Router

12V/1A Power Adapter

WAN

WLAN

PWR

WPS

WNRT-633

WAN

Wireless

WPS

Power

LAN1~LAN4

Cable

Modem

Ethernet Cable

Power

Adapter

WNRT-633

Line

ADSL

Phone

Splitter

Internet

Telephone wire

For security reasons it is recommended to change the password

at the first login and memorize it.

STEP 2: When the login window pops up, please enter the User

Name and Password. The default User Name and

Password are both “admin”.

Then click OK button to continue.

STEP 2: Highlight the wireless network (SSID) to connect and

click [Connect] button.

You have already finished the configuration of the WNRT-633.

Now you can use your iPhone, iPad, laptop, and any other Wi-Fi

device to connect with it wirelessly and start surfing the

internet.

STEP 4: Once the basic configuration of the router is done.

Click “Finished” button for the change to take effect.

STEP 3: After you enter into the Web User Interface, click

Wizard at the left hand side of the screen.

Please follow the indications on the screen to

quickly set up for the Internet connection.

5 dBi Antenna

Power

WPS/Reset

4 x Gigabit LAN Ports

Gigabit WAN Port

Power