PLANET WNAP-7335 User Manual

Hardware installation, Pole mounting further information: 6. web login

Note

– 1 –

– 2 –

– 3 –

– 4 –

1. Package Contents

2. Installation Precautions

3. Physical Introduction

– 7 –

– 8 –

– 5 –

– 6 –

The above steps introduce the simple installations

and configurations of the WNAP-7335. For further

configurations of different operation modes, please

refer to the user manual which can be downloaded

from the website.
http://www.planet.com.tw/en/support/download.p

hp?type1=4&model=48688&type=3
If you have further questions, please contact the local dealer or

distributor where you purchased this product.

2011-E10610-000

Thank you for choosing PLANET WNAP-7335. Before installing the

AP, please verify the contents inside the package box.

If there is any item missing or damaged, please

contact the seller immediately.

STEP 2: Plug the power cord into the DC port and the other

side into the AC socket. Then, plug the RJ45 cable

(as shown in picture 4 under Step 1) into the POE

port of the PoE injector.

STEP 1: (A) Push the latch on the bottom of the WNAP-7335

to remove the sliding cover.

Bottom Panel Description – Port

Connect the WNAP-7335 with your PC via the PoE injector where

one end of an Ethernet cable is plugged into the LAN port of the

PoE injector while the other end into the LAN port of the PC. Power

on the WNAP-7335 from the PoE injector.

1. Click the “Start” button located in the lower-left corner of

your computer.

2. Click “Control Panel”.
3. Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and

click “Properties”.

7. Select “Use the following IP address”, and then click

the “OK” button twice to save the configuration. For

example, as the default IP address of the WNAP-7335 is

192.168.1.253 and the router is 192.168.1.254, then you

may choose from 192.168.1.1 to 192.168.1.252.

Default IP Address: 192.168.1.253

Default Username: admin

Default Password: admin

Default SSID: WNAP-7335

STEP 1: The Web management allows you to access and

manage the wireless AP easily. Launch the Web

browser and enter the default IP address

http://192.168.1.253.

WNAP-7335

Quick Installation Guide

300Mbps 802.11a/n Wireless Outdoor CPE

For security reasons, it is recommended to change the

password at the first login and memorize it.

STEP 2: When the login window pops up, please enter the

User Name and Password. The default User Name

and Password are both “admin”. Then click the OK

button to continue.

STEP 3: After you enter into the Web User Interface, go to

Wireless Basic Settings to configure your wireless

network.

Rear Panel Description – LED Indication

Plastic Strap x 1

WNAP-7335

Quick Guide

PoE Injector & Power Cord

4. Hardware Installation

STEP 1:
Place the strap through

the slot on the back of

the WNAP-7335 and

then around the pole.

Tighten the strap to

secure the WNAP-7335.

5. Pole Mounting

Further Information:

6. Web Login

(B) Plug the RJ45 Ethernet cable into the PoE LAN Port and

connect the external antenna to the RP-SMA connectors of

the WNAP-7335. Then, slide back the cover of the

WNAP-7335 to finish the installation.

IMPORTANT SAFETY PRECAUTIONS:

1) LIVES MAY BE AT RISK! Please be aware of the

electrical wires around, and tighten the pole.

Carefully read the section "OUTDOOR

INSTALLATION WARNING" in the manual

before installation.

2) Users MUST use the “PoE Injector” and

“Power Cord” shipped in the box with the

WNAP-7335. Otherwise, the product might be

damaged.

3) Users MUST use a proper and well-installed

surge arrestor and grounding wired with the

WNAP-7335; otherwise, a sudden lightning could

cause fatal damage to the WNAP-7335. EMD

(Lightning) DAMAGE IS NOT COVERED

UNDER WARRANTY.

4) Users MUST have the antenna connected

first before powering on the WNAP-7335;

otherwise, damage to the WNAP-7335

might happen.

5) The Antenna is required, and must be purchased

separately.

Caution

Grounding Terminal

Reset Button

LAN2

PoE LAN

RP-SMA

RP-SMA(Male) to N-male Cable

Ethernet Cable

24V PoE Injector

Data

Power

Data

PoE Port

LAN

POE

PoE Out

Data In

Signal Indicator

LAN 2 LED

Power LED

LAN 1 LED