PLANET WNAP-6350 - Manual

Note
– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
3. Physical Introduction
2. Installation Precautions
– 7 – – 8 –
5. Web Login
– 5 – – 6 –
Mounting Kit x 1 RJ-45 Waterproof Kit x 2
FURTHER INFORMATION:
The above steps introduce simple installations and
configurations for the WNAP-6350. For further configurations
of different operation modes, please refer to the user’s
manual in the CD. If you have further questions, please
contact the local dealer or distributor where you purchased
this product.
2011-E10520-001
Thank you for choosing PLANET WNAP-6350. Before
installing the AP, please verify the contents inside the
package box.
If there is any item missing or damaged, please
contact the seller immediately.
Rear Panel Description – Port & Connector
STEP 4: Plug the other waterproof kit into the WAN/LAN
port to complete the installation.
STEP 3: Take out the power cord and PoE injector. Plug
the power cord into the DC port and plug the
other side of the RJ-45 cable into the POE port of
the PoE injector.
STEP 1: Plug the N-Type (M) to N-Type (M) RF cables into
the antenna connectors of the WNAP-6350, and
then connect the N-Type (F) antennas to the
other side of the RF cables.
Connect the WNAP-6350 with your PC by an Ethernet cable
plugging in LAN port of PoE injector in one side and in LAN
port of PC in the other side. Power on the WNAP-6350 by PoE
from PoE injector.
1. Assign a static IP address to your PC which should be in
the same network segment with the WNAP-6350. As
the default IP address of the WNAP-6350 is
192.168.1.1, you may choose from 192.168.1.2 to
192.168.1.254. Then click OK.
2. Open the web browser on your PC, key in the IP
address (192.168.1.1) of the WNAP-6350 in the
address bar, and then enter.
3. The default User Name and Password are both
“admin”. Enter them and then click OK.
Default IP Address: 192.168.1.1
Default User Name: admin
Default Password: admin
Default SSID: WNAP-6350
PoE Injector & Power Cord Quick Guide
WNAP-6350
Quick Installation Guide
300Mbps 802.11b/g/n
Wireless Outdoor AP
CD-ROM
WNAP-6350
1. Users MUST use a proper and well-installed surge
arrestor and grounding kit with WNAP-6350; otherwise, a
random lightning could easily cause fatal damage to
WNAP-6350. EMD (Lightning) DAMAGE IS NOT
COVERED UNDER WARRANTY.
2. Users MUST use the “Power cord and PoE Injector”
shipped in the box with the WNAP-6350. Use of other
options will cause damage to the WNAP-6350.
3. Users MUST power off the WNAP-6350 first before
connecting the external antennas to it; otherwise,
damage might be caused to the WNAP-6350 itself.
4. Now, you can see the Web management UI of the
WNAP-6350.
You can use Easy Setup at the top of the screen to
configure the WNAP-6350.
4. Hardware Installation
STEP 5a: Pole Mounting
(a.1) Attach the mounting bracket to the back of the
device by using four screws and flat washers.
(a.2) Assemble the M bracket on the outside of the
mounting bracket by using four screws and flat
washers.
(a.3) Install the mounting bracket assembly against the
pole by using the teeth bracket, and then tighten it
by four long screws.
STEP 5b: Wall Mounting
(b.1) Attach the mounting bracket to the back of the
device by using four screws and flat washers.
(b.2) Assemble the M bracket on the wall by using four
screws and flat washers.
(b.3) Install the mounting bracket assembly inside the M
bracket mounted in the wall by using four screws
and flat washers.
IMPORTANT SAFETY PRECAUTIONS:
1) LIVES MAY BE AT RISK! Please be aware of
the electric wires around, and tighten the
pole. Carefully read the section "OUTDOOR
INSTALLATION WARNING" in the manual
before installation.
2) Users MUST use the “Power cord and PoE
Injector” shipped in the box with the
WNAP-6350. Otherwise, the product might be
damaged.
STEP 2: Plug the RJ-45 Ethernet cable into the LAN Port of
WNAP-6350 through the waterproof kit.
(a.1) (a.2)
(a.3)
(b.1) (b.2)
(b.3)
Note
Caution
Pole diameter less than 5cm may require the use
of hex nuts to lock the long screws to the
suitable location.