PLANET POE-173 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Content
Thank you for purchasing PLANET Single-Port
10/100/1000Mbps Ultra PoE Injector, POE-173.
Model LAN Port Speed PoE Standard
PoE
Budget
POE-173 10/100/1000Mbps
Ultra PoE,
backward
compatible with
IEEE 802.3at/af
standard
60 watts
The term of “Ultra PoE Injector” in the following
section of this User’s Manual means the POE-173.
The box of the Single-Port 10/100/1000Mbps Ultra
PoE Injector should contain the following items:
 The Single-Port 10/100/1000Mbps Ultra PoE
Injector x 1
 User’s Manual x 1
 AC Power Cord x 1
If any of these are missing or damaged, please
contact your dealer immediately; if possible, retain
the carton including the original packing material,
and use them again to repack the product in case
there is a need to return it to us for repair.
2. Product Features
￭ Interface
 2 x RJ-45 interfaces
 1-Port Data + Power output
 1-Port Data input
 1 x AC 100-240V input power socket
￭ Power over Ethernet
 Ultra Power over Ethernet PSE
 Up to 60 watts of power on 4-pairs UTP
 Backward compatible with IEEE 802.3at/af PD
device
 Auto-detection of PoE IEEE 802.3at/af equip-
ment and devices from being damaged by
incorrect installation
 Remote power feeding up to 100m
￭ Hardware
 All-in-one compact size design
 Internal power supply
 LED indicators for Power LED and Active LED
(PoE ready / In-use)
Note
PSE (Power Sourcing Equipment) is
a device (switch, or hub for instance)
that will provide power in a PoE setup.
The maximum allowed continuous output
power per such device in IEEE 802.3af is
15.4 watts, in IEEE 802.3at is 30 watts
and Ultra PoE is 60 watts.
PD (Powered Device) such as IP
Phones, network cameras or Wireless
access points is a PoE-enabled terminal
by PSE and thus it consumes energy.
3. Product Specifications
Product POE-173
Hardware Specifications
Interface
LAN
1 x RJ-45 STP, “Data” Input
Port
POE
1 x RJ-45 STP, “Data + Power”
Output Port
AC
Connector 1 x AC Input power socket,
IEC-320 C6
Network
Cable
Ultra PoE
(60W) 4-pair UTP Cat. 5, 5e, 6 up to
100m (328ft)
802.3af / at
PoE (15W /
30W)
2-pair UTP Cat. 3, 4, 5, up to
100m (328ft)
LED Indicator
System: Power x 1 (Green)
PoE Port: Active, PoE ready /
In Use x 1 (Green)
Data Rate 10/100/1000Mbps
Dimensions
(W x D x H)
115 x 62.5 x 31 mm
Weight 177g
Unit Output Voltage DC 50V, 1.2A
Power Requirements
100-240V AC @50/60Hz,
1.5A max.
Power Consumption 60 Watts max.
Operating Temperature 0 ~ 50 degrees C
Storage Temperature
-10 ~ 70 degrees C
Operating Humidity
5 ~ 95%, Relative Humidity,
non-condensing
Storage Humidity
5 ~ 95%, Relative Humidity,
non-condensing
Power over Ethernet
PoE Standard
Ultra PoE over 4-pairs UTP,
IEEE 802.3at High Power over
Ethernet End-Span / Mid-Span
PSE
PoE Power Supply Type End-Span + Mid-Span
Power Pin Assignment
Pair 1 End-Span: 1/2(+), 3/6(-)
Pair 2 Mid-Span: 4/5(+), 7/8(-)
PoE Power Output
DC 50V / 60-watt PoE via 4-pairs
DC 50V / 30-watt PoE via 2-pairs
Standards Conformance
Standards Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast
Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
IEEE 802.3at Power over
Ethernet Plus
IEEE 802.3af Power over
Ethernet
Regulation Compliance FCC Part 15 Class B, CE
4. Product Outlook
Figure 1: An overview of Ultra PoE Injector.
Figure 1: POE-173 Outlook
LED Indicators
LED Color Function
POWER Green
Lights to indicate that the Ultra PoE
Injector has power.
ACTIVE Green
Lights to indicate the port is providing
50V DC in-line power.
5. Hardware Installation
The following section describes the hardware features
of Ultra PoE Injector. Before connecting any network
device to the Ultra PoE Injector, read this chapter
carefully.
This POE-173 provides three different running speeds
– 10Mbps / 100Mbps / 1000Mbps for automatically
distinguish the speed of incoming connection. Please
refer to the following sections for detailed information
about Ultra PoE Injector.
5-1. Before Installation
Before installation, it is recommended to check your
network environment. If there is any IEEE 802.3at
devices that need higher power to power on and
work normally, the Ultra PoE Injector can provide
you with power for this Ethernet device conveniently
and easily. The Ultra PoE Injector is equipped with
an AC power cord with 100-240V AC input and
injects DC 50V power into the pin of the twisted pair
cable (pair 1/2 [+], 3/6 [-] and pair 4/5[+], 7/8[-]).
If there is difficulty in finding a power socket for
AC-DC Adapter of your non-PoE network device, the
Ultra PoE Injector and POE-171S (Ultra PoE Splitter)
can provide you with DC power for this Ethernet
device conveniently and easily.
Note
The Ultra PoE Injector and POE-171S
can be installed in pair. However, the
use of third-party device is allowed if the
device complies with IEEE 802.3at Power
over Ethernet Plus and a maximum of
30 watts of output capability.
Note
Since the Ultra PoE Injector PoE port
supports 50V DC PoE power output,
please check and assure the Powered
Device’s (PD) acceptable DC power range
is 50V DC; otherwise, it will damage the
Powered Device (PD).
The Ultra PoE Injector Installation
Due to the backward capability of IEEE 802.3at/
af PoE standard, the Ultra PoE Injector can directly
connect with any IEEE 802.3at/af end-nodes such
as PTZ (Pan, Tilt & Zoom) speed dome network
cameras, color touch-screen Voice over IP (VoIP)
telephones, multi-channel wireless LAN access points.
The screen in Figure 2 appears.
Switch
100 meters
PoE
Power Data
PoE PTZ
IP Camera
POE-173
Ultra PoE Injector
Power
Data
AC
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Power Line (AC) AC
Figure 2: Connection to IEEE 802.3at / 802.3af Powered
Devices
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on
steadily.
2. Connect a standard network cable from Switch /
workstation to “LAN” port of Ultra PoE Injector.
3. Connect the long cable that will be used to
connect to the remote PoE PD device to the port
“POE”.
4. Connect with IEEE 802.3at/af devices