PLANET POE-173 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Single-Port
10/100/1000Mbps Ultra PoE Injector, POE-173.
Model LAN Port Speed PoE Standard
PoE
Budget
POE-173 10/100/1000Mbps
Ultra PoE,
backward
compatible with
IEEE 802.3at/af
standard
60 watts
The term “Ultra PoE Injector” in the following
section of this User’s Manual means the POE-173.
The box of the Single-Port 10/100/1000Mbps Ultra
PoE Injector should contain the following items:
 The Single-Port 10/100/1000Mbps Ultra PoE
Injector x 1
 User’s Manual x 1
 AC Power Cord x 1
If any of these are missing or damaged, please
contact your dealer immediately; if possible, retain
the carton including the original packing material,
and use them again to repack the product in case
there is a need to return it to us for repair.
2. Product Features
„ Interface

2 x RJ45 interface

1-Port Data + Power output
 1-Port Data input
 1 x AC 100-240V input power socket
„ Power over Ethernet

Ultra Power over Ethernet PSE
 Up to 60 watts of power on 4-pair UTP cable
 Backward compatible with IEEE 802.3at/af PD
device
 Auto-detection of PoE IEEE 802.3at/af equip-
ment and devices to check whether there’s any
damage done via incorrect installation
 Remote power feeding up to 100m
„ Hardware

All-in-one compact size design
 Internal power supply
 LED indicators for Power LED and Active LED
(PoE ready / In-use)
Note
PSE (Power Sourcing Equipment) is
a device (switch, or hub for instance)
that will provide power in a PoE setup.
The maximum allowed continuous output
power per such device in IEEE 802.3af is
15.4 watts, in IEEE 802.3at is 30 watts
and Ultra PoE is 60 watts.
Note
PD (Powered Device) such as IP
phones, network cameras or wireless
access points is a PoE-enabled terminal
by PSE and thus it consumes energy.
3. Product Specifications
Product POE-173
Hardware Specifications
Interface
LAN 1 x RJ45 STP, “Data” Input Port
PoE
1 x RJ45 STP, “Data + Power”
Output Port
AC
Connector
1 x AC input power socket,
IEC-320 C6
Network
Cable
Ultra PoE
(60W)
4-pair UTP Cat. 5, 5e, 6 up to
100m (328ft)
802.3af / at
PoE (15W /
30W)
2-pair UTP Cat. 3, 4, 5, up to
100m (328ft)
LED Indicator
System: Power x 1 (Green)
PoE Port: Active, PoE ready /
In Use x 1 (Green)
Data Rate 10/100/1000Mbps
Dimensions
(W x D x H)
115 x 62.5 x 31 mm
Weight 177g
Unit Output Voltage DC 50V, 1.2A
Power Requirements
100-240V AC @50/60Hz,
1.5A max.
Power Consumption 60 watts max.
Operating Temperature 0 ~ 50 degrees C
Storage Temperature
-10 ~ 70 degrees C
Operating Humidity
5 ~ 95%, Relative Humidity,
non-condensing
Storage Humidity
5 ~ 95%, Relative Humidity,
non-condensing
Power over Ethernet
PoE Standard
Ultra PoE over 4-pairs UTP cable,
IEEE 802.3at High Power over
Ethernet End-Span / Mid-Span
PSE
PoE Power Supply Type End-Span + Mid-Span
Power Pin Assignment Pair 1 End-Span: 1/2(+), 3/6(-)
Pair 2 Mid-Span: 4/5(+), 7/8(-)
PoE Power Output
DC 50V / 60-watt PoE via 4-pairs
DC 50V / 30-watt PoE via 2-pairs
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T
Gigabit Ethernet
IEEE 802.3at Power over
Ethernet Plus
IEEE 802.3af Power over Ethernet
Regulation Compliance FCC Part 15 Class B, CE
4. Product Outlook
Figure 1: An overview of Ultra PoE Injector.
Figure 1: POE-173 Outlook
LED Indicators
LED Color Function
POWER Green
It indicates that the Ultra PoE Injector
has power.
ACTIVE Green
It indicates the port is providing 50V DC
in-line power.
5. Hardware Installation
The following section describes the hardware
features of Ultra PoE Injector. Before connecting any
network device to the Ultra PoE Injector, read this
chapter carefully.
5-1. Before Installation
The POE-173 is backward compatible with IEEE
802.3af PoE and IEEE 802.3at high power PoE
standard. It is equipped with an AC power cord with
100-240V AC input and injects DC 50V power into
the pin of the twisted pair cable (pair 1/2 [+], 3/6
[-] and pair 4/5[+], 7/8[-]) for 60-watt Ultra PoE
injection.
Before connecting the POE-173 to your powered
device (PD), please check to ensure that your
powered device (PD) can accept 60-watt PoE power
through pin 1/2 (+) & 3/6 (-) and pin 4/5 (+) & 7/8
(-). Otherwise, it will damage your powered device
(PD).
Please also note: DO NOT connect POE-173 POE
port to your non-POE network equipment Ethernet
interface. Otherwise, it will damage your network
equipment.
If there is difficulty in finding a power socket for
AC-DC Adapter of your non-PoE network device, the
Ultra PoE Injector and POE-171S (Ultra PoE Splitter)
can provide you with DC power for this Ethernet
device conveniently and easily.
Note
The Ultra PoE Injector and POE-171S
can be installed in pair. However,
the use of the third-party device is
allowed if the device complies with
IEEE 802.3at Power over Ethernet Plus
and a maximum of 30 watts of output
capability.
Note
Since the ultra PoE injector PoE port
supports 50V DC PoE power output,
please check and assure the Powered
Device’s (PD) acceptable DC power
range is 50V DC; otherwise, it will
damage the Powered Device (PD).
Ultra PoE Injector Installation
Due to the backward capability of IEEE 802.3at/
af PoE standard, the Ultra PoE Injector can directly
connect with any IEEE 802.3at/af end-nodes such
as PTZ (Pan, Tilt & Zoom) speed dome network
cameras, color touch-screen voice over IP (VoIP)
telephones, and multi-channel wireless LAN access
points. The screen in Figure 2 is shown below.
Switch
100 meters
PoE
Power Data
PoE PTZ
IP Camera
POE-173
Ultra PoE Injector
Power
Data
AC
1000BASE-T UTP
PoE 1000BASE-T UTP with PoE
Power Line (AC) AC
Figure 2: Connection to IEEE 802.3at / 802.3af Powered
Devices
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on
steadily.
2. Connect a standard network cable from Switch /
workstation to “LAN” port of Ultra PoE Injector.
3. Connect the long cable to the port (PoE) of the
remote PoE PD device.
4. Connect with IEEE 802.3at/af devices.
Once Ultra PoE Injector detects the existence of
an IEEE 802.3at / 802.3af device, the ACTIVE LED
indicator will be on steadily to show it is providing
power.