PLANET XGS3-24040 - Manual (Page 2)

Follow these steps to install the optional module into the
Switch:
1. Place the Switch on a flat surface. Grasp the thumbscrew
on the sides of the blank bracket and turn counter-
clockwise to unscrew them. You can also use a screw-
driver remove the blank bracket (See Figure 2). Do not
discard the blank bracket. Put the blank bracket back if
you remove the module out of the Switch.
RPSDC In 12V-13A M1
M2
Up Down
100~240V~ 50-60Hz 2A
Figure 2 Remove the blank bracket
2. Install the XGS3-XFP module by inserting it into the rails
and sliding it in until it stops (See Figure 3). Press it
firmly until you feel the module snap into place. Never
force, twist or bend the optional module.
3. Gently push the thumbscrews and turn clockwise to
tighten. Do not over tighten the thumbscrews.
4. Turn on the Switch and it will automatically detect the
new module.
RPSDC In 12V-13
A M1
M2
Up
Down
100~240V~ 50-60Hz 2A
1-Port 10G XFP Modu le
XGS3-XFP
LNK/ACT
Figure 3 Insert the XGS3-XFP modules
5. Check the LED on the XFP module’s front panel to verify
that if there is a link and a proper connection at the port.
Please refer to the Switch’s user’s manual for more about
Switch or XGS3-XFP module’s management.
5. XFP Transceiver Installation
The XGS3-XFP has one vacant 10Gb fiber transceiver slot.
The procedure of installing the XFP 10Gb fiber transceiver
is as below:
Installing the XFP transceiver
1. Put on an ESD wrist strap (or antistatic gloves)
2. Insert the XFP transceiver to the guide rail inside the
XGS3-XFP module. Do not to put the XFP transceiver up-
side-down.
n
3. Push the XFP transceiver along the guide rail gently until
it comes into contact with the front panel of the XGS3-
XFP module.
RPSDC In 12V-13A M1
M2
Up
Down
100~240V~ 50-60Hz 2A
1-Port 10G XFP Modu le
XGS3-XFP
LNK/ACT
Figure 4 Plug-in the XFP transceiver
Note
The XFP 10Gb transceiver is hot-swappable.
Caution
Do not stare directly at the 2 fiber bore in the
XFP transceiver when the Switch is in operation,
otherwise the laser may hurt your eyes.
Connect the fiber cable
1. Make sure both side of the XFP transceiver are with the
same media type, for example: 10GBase-SR to 10GBase-
SR, 10GBase-LR to 10GBase-LR.
2. Check the fiber-optic cable type match the XFP trans-
ceiver model.
n
3. Attach the duplex LC connector on the network cable into
the XFP transceiver.
4. Connect the other end of the cable to a device – switches
with XFP or SFP+ installed, fiber NIC on a workstation or
a Media Converter.
5. Check the LNK/ACT LED of the XGS3-XFP module. Ensure
that the XFP transceiver is operating correctly.
APPENDIX A
Fiber Optical Cable Connection Parameters
The wiring details are as below:
Fiber Optical patch Cables:
Standard Wavelength Fiber Type
Cable
Specification
10GBase-SR 850nm Multi-mode 50/125μm
10GBase-LR 1310nm Single mode 9/125μm
n
5 6
7 8