PLANET GSD-803PD - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
 Gigabit Ethernet PoE PD Switch x 1
 User's Manual x 1
 Rubber Feet x 4
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
3. Switch Front Panel
Figure 3-1 shows the front panel of GSD-803PD.
GSD-803PD PWR 1000
1 2 3 4 5 6 7 8 PoE PD
LNK ACT
8-Port Gigabit Ethernet Switch
10/100 LNK ACT
Figure 3-1: GSD-803PD Front Panel
Step 4: Connect your Gigabit Ethernet PoE PD Switch to
network devices.
A. Connect one end of a standard network
cable to the 10/100/1000Mbps RJ-45 ports
on the Back of the Gigabit Ethernet PoE PD
Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers..
Step 5: Supply power to the Gigabit Ethernet PoE PD
Switch.
A. Connect one end of the RJ-45 UTP cable
from 802.3af PoE PSE devices to the port 8
of Gigabit Ethernet PoE PD Switch.
When the Gigabit Ethernet PoE PD Switch receives
power, the Power LED should remain solid Green.
5. Switch Rear Panel
Figure 5-1 shows the rear panel of GSD-803PD.
5V DC
1 3 5 7 4 6 8
PoE PD
2 ON
OFF
Figure 5-1: GSD-803PD Rear Panel
Power
Notice
1. The Gigabit Ethernet PoE PD Switch
supports two power systems, DC 5V or
powered from PoE Port # 8 that supports
802.3af PoE 48V DC in-line power.
2. The default package of Gigabit Ethernet
PoE PD Switch does not include DC 5V
power adapter. If you need this DC 5V
power adapter, please contact your local
dealer or distributor for more assistance.
2. Product Features
 Complies with IEEE 802.3 10Base-T, IEEE 802.3u
100Base-TX, IEEE 802.3ab 1000Base-T Ethernet
standard
 8-Port 10/100/1000Mbps Gigabit Ethernet Ports
 Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
 Hardware based 10/100Mbps, half / full duplex and
1000Mbps full duplex mode, flow control and auto-
negotiation
 IEEE 802.3x flow control for full duplex operation and
back-pressure for half duplex operation
 Integrated address look-up engine, support 8K
absolute MAC addresses
 One power on/off button for energy saving
 Automatic address learning and address aging
 9K Jumbo packet size
 Supports Auto MDI/MDI-X function
 Support CSMA/CD protocol
 1-Port support 802.3af PoE DC 48V in-line power at
Port 8
 FCC, CE class A compliant
4. LED Indicators
 System
LED Color Function
PWR Green
Light to indicate that the Switch has
power.
 Per 10/100/1000Base-T RJ-45 Port
LED Color Function
1000
LNK/ACT
Orange
Light to indicate that the Switch
is successfully connecting to
the network at 1000Mbps.
Blink to indicate that the Switch is
actively sending or receiving
data over that port.
10/100
LNK/ACT
Green
Light to indicate that the Switch
is successfully connecting to
the network at 10/100Mbps.
Blink to indicate that the Switch is
actively sending or receiving
data over that port.
7. Product Specifications
Product GSD-803PD
Hardware Specifications
10/100/1000Base-T
Ports
8 Auto MDI/MDIX ports
Enclosure Metal
LED Indication
System: Power (Green)
Per Port: 1000 LNK/ACT (Orange)
10/100 LNK/ACT (Green)
Dimensions
(W x D x H)
155 mm x 86 mm x 26 mm
Weight 378g
Power
Requirements
802.3af PoE 48V DC in-line power
DC 5V power adapter (Not
include in standard package)
Power Consumption
/ Dissipation
3.3 watts / 11 BTU
Switch Specifications
Switch Processing
Scheme
Store-and-Forward
MAC Address Table 8K entries
Flow Control
Back pressure for Half Duplex
IEEE 802.3x Pause Frame for Full
Duplex
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
PoE PD Switch and make connections to it. Please
read the following topics and follow the procedures as
presented.
Note
This Gigabit Ethernet PoE PD Switch does
not need software configuration.
Desktop Installation
To install the Gigabit Ethernet PoE PD Switch on
desktop, simply follow the following steps:
Step 1: Attach the rubber feet to the recessed areas
on the bottom of the Gigabit Ethernet PoE PD
Switch.
Step 2: Place the Gigabit Ethernet PoE PD Switch on
desktop near an 802.3af PoE PSE device.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet PoE PD Switch and the
surrounding objects.
Note
When choosing a location, please keep
in mind the environmental restrictions
discussed in Chapter 7 -- Product
Specifications.