beautypg.com

Customer support, Rack mounting – PLANET FNSW-4800 User Manual

Page 2

background image

- 9 -

- 10 -

- 11 -

- 12 -

- 13 -

- 14 -

Step 5: Supply power to the Fast Ethernet Switch.

A. Connect one end of the power cable to the Fast

Ethernet Switch.

B. Connect the power plug of the power cable to

a standard wall outlet.

When the Fast Ethernet Switch receives power, the Power
LED should remain solid green.

Rack Mounting

To install the Fast Ethernet Switch in a 19-inch standard
rack, follow the instructions described below.

Step 1: Place your Fast Ethernet Switch on a hard flat

surface, with the front panel positioned towards
your front side.

Step 2: Attach a rack-mount bracket to each side of the

Switch with supplied screws attached to the
package. Figure 3 shows how to attach brackets to
one side of the Fast Ethernet Switch.

FNSW-4800

48-Port 10/100M

bps Fast Ethernet Switch

Figure 3: Attaching the brackets to the Fast Ethernet Switch

Step 6: Proceed with Steps 4 and 5 of Department

Networking Installation to connect the network
cabling and supply power to your Fast Ethernet
Switch.

Caution

You must use the screws supplied with the
mounting brackets. Damage caused to
the parts by using incorrect screws would
invalidate your warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second

bracket to the opposite side.

Step 5: After the brackets are attached to the Fast

Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in Figure
4.

Figure 4: Mounting the Fast Ethernet Switch on a Rack

Customer Support

Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site first to
check if it could solve you issue. If you need more support
information, please contact PLANET switch support team.

PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address:
[email protected]

Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology
Corp. All other trademarks belong to their respective
owners.

EC Declaration of Conformity

For the following equipment:

*Type of Product: 48-Port 10/100Base-TX Fast Ethernet Switch

*Model Number: FNSW-4800

* Produced by:

Manufacturer‘s Name :

Planet Technology Corp.

Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

New Taipei City 231, Taiwan (R.O.C.)

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on (2004/108/EC).

For the evaluation regarding the EMC, the following standards were applied:

EN55022

(2010 + AC:2011)

EN 61000-3-2

(2006+A1:2009+A2:2009)

EN 61000-3-3

(2008)

EN55024

(2010)

IEC 61000-4-2

(2008)

IEC 61000-4-3

(2010)

IEC 61000-4-4

(2012)

IEC 61000-4-5

(2005)

IEC 61000-4-6

(2008)

IEC 61000-4-8

(2009)

IEC 61000-4-11

(2004)

EN60950-1

(2006 + A11:2009 + A1:2010 +

A12:2011)

Responsible for marking this declaration if the:

Manufacturer

Authorized representative established within the EU

Authorized representative established within the EU (if applicable):
Company Name:

Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname

Kent Kang

Position / Title :

Product Manager

Taiwan

29

th

Nov., 2013

Place

Date

Legal Signature

PLANET TECHNOLOGY CORPORATION

e-mail: [email protected] http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528