Sealey CX101D - Manual

InstructIons for:
EXTRA HEAVY DUTY GARAGE/WORKSHOP TROLLEY
MoDEL no.
CX101D
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/
OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3. CONTENTS
2. DESCRIPTION
1.1. GENERAL SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this trolley.

Always load evenly with the centre of gravity of the load as near centre of the trolley as
possible.
 DO NOT overload the trolley - see 2. DESCRIPTION.

use the trolley in a suitable work area.

Keep the work area clean, uncluttered and ensure there is adequate lighting.

Keep the trolley clean and tidy in accordance with good workshop practice.

DO NOT use the trolley for any purpose other than that for which it is designed.

DO NOT stand on the trolley, use it as a ladder or allow others to ride on the trolley.

use the wheel locks to prevent the trolley from inadvertently moving.

DO NOT leave unattended, especially when loaded, unless the wheels are locked, chocked or
the trolley otherwise secured.

DO NOT use trolley on uneven ground and do not run over curbs or steps - use a ramp.

DO NOT use trolley if any part is significantly damaged, paying particular attention to the wheels.

Keep children and unauthorised persons away from the work area.
Note! Opening heavily laden drawer may result in instability, particularly if shelves are empty.
carefully unpack the product and check the contents against
the diagram and parts list below. should any items be missing
or damaged contact your sealey dealer.
4. ASSEMbLY
5. PARTS
Item Part No: Description
1 cX101D.01 BoLt M6 X 32mm
2 cX101D.02 trAY
3 cX101D.03 HAnDLE (EnD frAME)
4 cX101D.04 cAstor WHEEL c/w BrAKE
5 cX101D.05 cAstor WHEEL
6 cX101D.06 BoLt M6 X 12mm
7 cX101D.07 tooL cHEst
8 cX101D.08 WAsHEr
9 cX101D.09 sPrInG WAsHEr
10 cX101D.10 nut
11 cX101D.11 BoLt M6 X 40mm
Garage or workshop trolley with a total capacity of 80kg. Deep-walled shelves, each of which may be installed base down or base up to give either
tool and component security or unobstructed access. cX101D has a full-width, lockable drawer, four large castors, two with a brake.
4.1. Mount tray (2) to the upper hole in the end frames (3)
and loosely fix with four M6 x 32mm bolts (1). Make
sure the dished holes on the end frames are facing
outwards.
4.2. Mount the other tray (2) to the lower hole in the
end frames (3) and loosely fix with four M6 x 32mm
bolts (1).
4.3. Mount drawer assembly (7) to the middle hole in the
end frames (3) and loosely fix with four M6 x 40mm
bolts (11).
4.4. tighten all bolts (1).
4.5. turn the trolley over, install castors (4 &5 ) into the
bottom of the end frames and fix with the M6 x 12mm
bolts (6).
4.6. turn the trolley upright. the trolley is ready to use.
NOTE! There are two keys supplied to lock the drawer.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park ,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
email
Original Language Version
cX101D Issue no.3 23/03/11