Sealey FH01 User Manual
Fig.1, Fig.2, Maintenance
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Ensure that the lifting hoist is in good working order. Take action for
immediate repair. The use of unauthorised parts may be dangerous and
will invalidate the warranty.
Operate the lifting hoist in a suitable, well lit work area.
Keep work area clean and tidy and free from unrelated materials.
Ensure all non-essential persons keep a safe distance whilst lifting.
Always screw clamp frame to forks.
DO NOT use to lift personnel.
DO NOT carry loads over personnel.
DO NOT leave suspended loads unattended.
DO NOT use the lifting hoist if damaged.
DO NOT allow untrained persons to operate the lifting hoist.
DO NOT exceed the rated capacity of the lifting hoist.
DO NOT manually carry assembled heist by the hook.
When not in use, store in a safe, dry, childproof area.
✓
Before lifting the load ensure that the forks are in the lowest practical
position, that there are no obstacles which may snag the load whilst it is
being lifted and that the area above the forks is clear.
✓
To avoid injury, be fully aware of your own and other persons locations in
relation to the lifting, and lowering, of the load.
✓
Ensure the centre of gravity always remains inside the forks.
✗
DO NOT harness the load at an angle or use any attachments not verified
as fit for purpose.
✗
DO NOT allow the load to swing during lifting/transporting.
✗
DO NOT allow the load to drop suddenly. Lower load with care, ensuring
that you are fully aware of the condition of the surface onto which the load
is to be placed.
✗
DO NOT use this product to perform a task for which it is not designed.
✗
DO NOT use whilst under the influence of drugs, alcohol or intoxicating
medication.
✗
DO NOT climb on the forks.
WARNING! Failure to heed safety and warning instructions may result
in damage and/or personal injury and will invalidate the warranty
.
2. INTRODUCTION & SPECIFICATION
3. ASSEMBLY INSTRUCTIONS/PARTS
1. SAFETY INSTRUCTIONS
2.1. Manufactured from heavy-duty steel for added strength. Easily converts a
forklift into a mobile crane. Fitted with an opening hook for use with
multiple attachments. Safely secures to forklift using 2 heavy-duty tommy
bar screws.
2.2. Maximum Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000kg
Fork Opening Pitch: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mm
Fork Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 x 65mm
Overall Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440 x 120 x 160mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14kg
FH01 Issue No.1 - 23/10/13
3.1. Check contents from list and fig.1. In the unlikely event of missing or
damaged parts consult your Sealey dealer immediately.
3.1.1 Initial assembly with the fork lift truck primed for use as in fig.2, the forks
pitched at 250mm centrally positioned and raised to a convenient height.
3.1.2 Offer the lifting hoist frame (1) on to the forks and slide toward the main
body of the fork lift as far as the apparatus to be lifted will allow.
3.1.3 Clamp the lifting hoist frame with the two tommy bar screws (4).
3.1.4
Remove the shackle-pin and loop the shackle (3) through the hook eye.
3.1.5
Offer the hook (2) and shackle up to the lifting hoist frame lug and
insert the shackle pin. Tighten with a tommy bar or spanner.
Original Language Version
© Jack Sealey Limited
INSTRUCTIONS FOR:
FORKLIFT LIFTING HOIST 1000kg CAPACITY
MODEL No:
FH01
250mm Fork Pitch
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a manner
which is compatible with the environment.
1
2
3
4
Item Description
1 Frame
2
Hook Assembly
3 Shackle
4
Tommy Bar Screw
4. MAINTENANCE
4.1. Inspect items after each use for integrity, missing parts and damage.
4.2. Clean with dry or lightly oiled cloth and store indoors.
fig.1
Tighten
fig.2