Casio XW-G1 - Manual (Page 75)

Using the Performance Mode
E-73
Editable Parameter List
Master EQ
Master Equalizer. Turning on this setting filters out master equalizer items contained in the Effect
Parameter group of the Editable Performance Parameter List (page E-73).
Off, On
Looper
Sample looper. While this setting is turned on, you will not be able to call up the sample looper
items in the Sequencer Parameter group of the Editable Performance Parameter List (page
E-73).
Off, On
Multifunc Key
Multi-function Key. While this setting is turned on, you will not be able to call up the sample looper
items in the Multi-Function Key Parameter group of the Editable Performance Parameter List
(page E-73).
Off, On
Editable Performance Parameter List
Display Description Settings
Zone Param >Ent
Zone parameters. This group includes parameters for each of the zones (Zone 1 through 4).
• Use the
9 PART minus (–) and plus (+) buttons to select the zone you want to edit.
• You also can enter the group using the following shortcut: Perform step 2 under “To register a
performance” (page E-71) and then hold down
7
EDIT. This will enter the group.
Zone
Zone on/off. Turns all zones on or off This setting is different from the mixer function page (page
E-80) part on/off (Part Enable) setting.
Off, On
Tone
Tone. Selects the tone for each zone. This setting is the same as the mixer function part tone
(page E-80).
• While this item is selected, you can select a tone using the same operation as that used in the
Tone Mode.
• This setting can also be configured using quick editing (page E-16).
• There are some limitations on the selection of tone categories for Zones 2 through 4 (page
E-16).
• A tone with DSP will have DSP next to the tone name on the display (page E-36).
Zone 1:
Solo Synth P000 to
PCM Drum U309
Zone 2 to 4:
PCM Tone P100 to
PCM Drum U309
KeyRangeLow
Key range low. Specifies the low key range of the keyboard for each zone. This setting is used in
combination with the Key Range Hi setting to configure key ranges for each zone.
For example, configuring F3 (low) to C7 (high) for Zones 1 and 2 and C2 (low) to E3 (high) for
Zones 3 and 4 will enable play of Zone 1 and 2 tones on the right side keyboard range in the
illustration below, and the Zone 3 and 4 tones on the left side keyboard.
• Setting can be specified using the keyboard keys.
C- to G9 *
KeyRangeHi
Key range high. Specifies the high range of the keyboard for each zone. This setting is used in
combination with the Key Range Lo setting to configure key ranges for each zone.
• Setting can be specified using the keyboard keys.
C- to G9 *
Volume Volume. This setting is the same as the mixer function tone volume (page E-80). 0 to 127
Pan
Pan. Adjusts the left-right position of sound in the stereo field. This setting is the same as the
mixer function part panning (page E-80).
–64 to 0 to +63
Oct.Shift Octave shift. Shifts the tone of notes by octave units. –2 to 0 to +2
Transpose
Transpose. Shifts the tone of notes by semitone units. This setting is the same as the mixer
function part coarse tune (page E-80).
–12 to 0 to +12
FineTune Fine tune. This setting is the same as the mixer function part fine tune (page E-80). –99 to 0 to +99
BendRngDwn Bend range down. Pitch change amount for downward bender operation. 0 to 24
BendRngUp Bend range up. Pitch change amount for upward bender operation. 0 to 24
Rev Send Reverb send. This setting is the same as the mixer reverb send (page E-80). 0 to 127
Cho Send Chorus send. This setting is the same as the mixer chorus send (page E-80). 0 to 127
Display Description Settings
C2 F3 E3 C7
Zone 3
Zone 4 Zone 1
Zone 2