Crelando 48420 - Manual

EN
IE
Instructions for Use
No. 48420
Tjanting Set
Intended use
The electric Tjanting tool is solely intended for private non-commercial
use in dry interior areas. It is a tool for individual creating batik patterns
on fabric (like cotton, linen, half-linen, etc.) by means of liquid wax. Any
other use is not permitted and can lead to injuries. In these cases the
manufacturer carries no liability. The electric Tjanting tool is used to
apply wax easily on fabric you want to design. After the wax has cooled
down, put the fabric into the batik color (not included, observe the in-
structions of the manufacturer of the batik color). Areas waxed on the
fabric will remain uncolored. Wax batik is a fabric dyeing process where
areas which are not to be dyed are covered with liquid wax.
Safety instructions
• CAUTION! When not in use, this device must be placed on the security
stand (pos. VI).
• When the device is placed on the stand, the surface underneath must
be firm, not flammable and horizontal.
• This appliance can be used by children from 8 years on as well as
by persons with restricted physical, sensory or intellectual abilities or
lacking experience and knowledge if they are supervised or if they re-
ceived instructions on how to use the appliance and they understand
the consequential hazards. Children are not allowed to play with the
appliance. Cleaning and maintenance must not be carried out by chil-
dren without supervision.
• In order to avoid hazards, if the mains connection of this appliance is
damaged, it must be replaced by the manufacturer or his customer
service or a similarly qualified person.
• A fire can break out if the appliance is not handled carefully.
• Ensure that the connecting cable does not come into contact with
heat, oil or sharp edges. Damaged connecting cables can cause fires,
short-circuits and electric shocks.
• Before use, remove combustible objects, liquids and gases from the
working area of the appliance. Keep your working area clean in order
to prevent accidents.
• Before use, check that the wax pot is correctly attached to the appli-
ance. The hot wax pot and its holder must not be brought into contact
with skin, hair, etc. Risk of burns!
• After use, place the device on the stand and allow it to cool down be-
fore packing it away.
• As long as it is in use, do not leave the appliance unsupervised.
• When the appliance is not in use, store it in a safe place protected from
dust and moisture.
• Check the appliance for damage. Do not use if damaged!
• During use, ensure adequate ventilation. Ensure that no poisonous
gases or vapours can be inhaled. Wear protective clothing.
• For longer work interruptions, disconnect the appliance from the volt-
age source.
• Observe national and international safety, health and work protection
regulations.
Preparation
Please take your time and read the operating instructions carefully be-
fore putting the appliance into operation and keep the operating instruc-
tions for future reference.
It is not allowed to change settings or make modifications from those set
by the manufacturer. It could be dangerous to change the structure of
the device on your own authority, to remove parts or to use parts which
are not approved by the manufacturer. (If you change the structure of
the device on your own authority you risk e.g. an electric shock, a short
circuit and burns.)
Scope of delivery
1 Tjanting tool
1 wax pot
1 safety stand
1 package wax (approx. 25 g)
1 Operating Instructions
Please check the goods for completeness.
Explanation of the pictures
j Tjanting tool
k wax pot
l wax
m safety stand
Explanation of the symbols
Do not touch the tip of the tool (wax pot) during operation! The tip
is very hot! The same applies for the metallic tool holder as well as
the upper part of the stand. Risk of burns!
Do not emerge the appliance into water and do not expose it to
moisture. Risk of electric shock!
The temperature of the wax pot as well as the liquid wax is very
high during operation! Risk of burns!
Put away the Tjanting tool correctly on the stand, if is on and not in
use (pos. VI).
Important information before start up
• Read the security instructions before putting the device into operation!
• Ensure that the working area is clean, even and dry.
• Before commencing, unpack the Tjanting Set completely and check
the contents.
• The Tjanting tool and the wax pot are not pre-assembled for the initial
start-up. The wax pot must be screwed on the device (see pos. I and
II). To do so, you need a crosshead screwdriver (not included). In Tja-
nting devices which are operated electrically, the wax is melted directly
in the wax pot and kept liquid at constant temperature. This ensures
constant and steady work.
• When processing multilayer fabrics (working with wax e.g. on the front
side of a T-shirt) we recommend putting a protection ply (e.g. baking
parchment) under the working area. This protection ply prevents un-
intentional penetrating of the liquid wax on fabric areas which are not
intended for dyeing.
3452_cfhl_fly_GB_cs6.indd 1 14.08.14 08:42