Epson 10+ - Manual (Page 7)

EPSON PowerLite Home 10 Projector
7/03 EPSON PowerLite Home 10 Projector - 7
❏ If you’re using Windows, ® hold down the Fn key and press
the function key that lets you display on an external
monitor. It may have an icon such as
, or it may be
labelled CRT/LCD . (Allow a few seconds for the projector to
sync up after pressing it.)
The remote control doesn’t work
❏ Make sure you’ve removed the battery insulating tape. See
the Quick Setup sheet for instructions.
❏ Make sure you’re within 20 feet of the projector.
❏ Point the remote control at one of the projector’s two
infrared receivers. You should be within range of the infrared
receivers (about 30° left or right, and 15° above or below).
❏ You may need to replace the remote control’s battery. See
page 9 for details.
❏ Dim the room lights and turn off any fluorescent lights.
Make sure the projector is not in direct sunlight.
❏ Remove the clear film covering the infrared receivers.
❏ Turn off nearby equipment that emits infrared energy, such
as a radiant room heater.
Only part of the picture is displayed, or
the picture is distorted.
❏ Press the
Aspect button to select a different aspect ratio.
❏ If the image is distorted or contains interference, make sure
the cable is securely connected at both ends.
❏ If the image looks like
or , press the and
buttons on the projector’s control panel.
The picture is upside-down or reversed.
Change the Projection option in the setting menu.
The picture is blurry
❏ There may be dirt on the lens. Clean the lens with a canister
of compressed air or lens-cleaning paper. If necessary,
moisten a soft cloth with lens cleaner and gently wipe the
lens surface. Never rub the lens with abrasive materials.
❏ Adjust the focus ring.
❏ Adjust the
Sharpness setting on the Image menu.
❏ If you’re projecting from a computer, press the
Auto button
on the remote control to automatically optimize the image.
The colors on the screen don’t look right
❏ Press the
Color Mode button on the remote control to move
through the different color mode settings.
❏ If the picture looks too dark, you may need to replace the
lamp. See page 10 for details.
❏ You may be using the wrong source setting. Press the
Source button on the projector, or the Input A/B or
S-Video/Video buttons on the remote control to move
through the source settings.
❏ Adjust the following settings in the projector’s Image menu
under Picture Quality : Brightness , Contrast , Saturation
(video only), Tint (video only), Color Temperature , and
Flesh Tone .
The picture contains static or noise.
❏ Make sure your cable is securely connected at both ends.
❏ Don’t use an extension cable or a cable longer than 6 feet.
❏ If you’re displaying the same image on your computer and
projector screen, try turning off your laptop’s LCD display.
The projector and notebook don’t display
the same image
If you’re using Windows:
❏ On most systems, the or CRT/LCD key lets you
toggle between the LCD screen and the projector, or display
on both at the same time.
❏ You might need to use the Display utility in the Control
Panel to enable both the LCD screen and external monitor
port. Check your notebook’s manual or online help.
❏ If you have dual monitor support, you may need to uncheck
the option to extend your Windows desktop in the Display
Properties.
If you’re using Mac OS ® X:
1. Select System Preferences from the Apple ® menu and
click Displays .
2. Click Detect Displays .
3. To display the entire desktop on both your projector screen
and LCD screen, click the Arrangement or Arrange tab.
(If you don’t see this tab, make sure it isn’t hidden by
another window on your screen.)
Click here