ShoreLand'r SDV1831B User Manual
Final assembly instructions bundles required

SD-V1831 B & SD-GV1831 B
Parts Manual
SD-V1831 B
SeaDoo 3100 V-Frame Trailer - Wht
1 62340
Literature Bag - Trailers
1 6599801
Frame Bundle SD-V1831 Wht
2 4300199
ST215/75R14C Tire/MSilver Dir Rim
Tire Size &
Carrying Capacity Chart
Tongue Weight Adjustment
Tire
Load
Carrying
Size
Range
Capacity
ST215/75R14
C
1870 lbs.per/tire
Approximate Tongue Weight for Best Towing.
Tongue weight too high, move the axle assembly forward.
Tongue weight too low, move the axle assembly back-
ward. Tongue weight should be 5-7% of the total gross
weight of the boat and trailer combined.
Final Assembly Instructions
Bundles Required
SD-GV1831 B
SeaDoo 3100 V-Frame Trailer - Galv
1 62340
Literature Bag - Trailers
1 6599800
Frame Bundle SD-V1831 Galv
2 4300198
ST215/75R14C Tire/Galv Dir Rim
Remove the small parts from the frame by cutting the
bands. Remove the bolt bag and sort all the nuts and bolts
by size.
Springs:
Mount the springs to the axle with 1/2 X 6-1/2 axle u-bolt
from the top down. Install the spring clamp (Ref.#92) on
top of the spring under the u-bolts. Install the spring plate
(Ref.#94) under the axle. Tighten 1/2 flange lock nuts
evenly.
Axle:
Place one of the spring bushings (Ref.#90) into the rear of
the spring bracket and secure with 9/16 X 3-1/4 hex and
lock nut. Position the axle under the frame, then hook the
spring loop around the bushing already installed. Raise the
axle assembly up so the front of the springs line up with
the front spring bracket hole. Insert the two (2) 9/16 X 3-
1/4 and secure with 9/16 hex lock nuts. Tighten all nuts
and bolts but do not over tighten. Allow the spring room
enough to move.
Mount the tires and rims using 80-90 ft. lbs. torque on lug
nuts using proper tightening procedures.
Tongue:
Install the tongue into the nose cone of the trailer frame.
Thread the tongue harness through the tongue plate
cover. Secure the tongue plate cover (Ref.#82) and the
rear of the tongue with a 1/2 X 1-1/2 hex bolt, 1/2 flat
washer and 1/2 hex lock nut. Tighten. Match the tongue
harness wires with the correct frame harness wires, plug-
in. The wiring is complete.
Actuator & Safety Chain:
Slide the actuator (Ref.#61) into the actuator housing unit
(Ref.#96) and secure with two (2) pins and snap rings
provided with the actuator. Secure the actuator-housing to
the front of the tongue using three (3) 1/2 X 4 hex bolts
and 1/2 flange lock nuts. Using the 1/2 X 5 hex bolt on
the lower right mounting hole on the tongue, secure the
safety chain. Place a 1/2 flat washer on the 1/2 X 5 hex
bolt followed by one (1) safety chain and insert into the
actuator housing unit and tongue. Place the second safety
chain on the bolt followed by a 1/2 flat washer and 1/2
flange lock nut. Tighten.
Brakes:
Refer to the brake manual for service and maintenance.
Winch:
Mount the Profile 2000 winch assembly with the jack on
the tongue a desired location that best fits your watercraft
using three (3) 1/2 X 4 carriage bolts and 1/2 flange lock
nuts. Install the winch handle on the Profile 2000 winch
shaft.