ShoreLand'r LI-V1620 User Manual
Final assembly instructions, Bundles required

LI-V1620, LI-GV1620, & LI-BKV1620
Parts Manual
LI-V1620 Leisure Ind. V-Frame White
1 62340
Literature Bag - Trailers
1 6589401
Frame Bundle V1620 Wht
2 4300214
ST175/80R13C Tire/MSilver Dir Rim
1 3310050
Jack 800 lbs. - Swivel
1 3310053
Jack Mounting Hardware Bag
LI-GV1620 Leisure Ind. V-Frame Galv.
1
62340 Literature Bag - Trailers
1 6589400
Frame Bundle V1620 Galv
1 4300213
ST175/80R13C Tire/Galv. Dir Rim
1 3310050
Jack 800 lbs. - Swivel
1 3310053
Jack Mounting Hardware Bag
LI-BKV1620
Leisure Ind. V-Frame Black
1 62340
Literature Bag - Trailers
1 6589403
Frame Bundle V1620 Black
1 4300214
ST175/80R13CTire/MSlvr Dir Rim
1 3310050
Jack 800 lbs. - Swivel
1 3310053
Jack Mounting Hardware Bag
Tire Size &
Carrying Capacity Chart
Tongue Weight Adjustment
Tire
Load
Carrying
Size
Range
Capacity
ST175/80R13 C
1360 lbs.per/tire
Approximate Tongue Weight for Best Towing.
Tongue weight too high, move the axle assembly forward.
Tongue weight too low, move the axle assembly back-
ward. Tongue weight should be 5-7% of the total gross
weight of the boat and trailer combined.
Final Assembly Instructions
Remove the small parts from the frame by cutting the
bands. Remove the bolt bag and sort all nuts and bolts by
size.
Tongue:
Telescope the tongue out and install the tongue cover
(Ref.#60) onto the tongue frame cap and tongue using a
1/2 X 1-1/2 hex bolt. Secure with 1/2 flat washer and 1/
2 hex nut. Secure the tongue into the side frame tongue
cap using a 1/2 X 4 hex bolt and 1/2 flange lock nut.
Tongue Wires:
Install the tongue wire harness through the top forward
wire hole and exit the rear of the tongue channel on frame.
Install grommets and plug tongue wire into the frame
harness by color code.
Safety Chain:
Insert a 3/8 X 1-1/4 hex bolt with a 3/8 flat washer
and safety chain through the lower hole on the front of the
tongue. Secure with a 3/8 flat washer and 3/8 flange lock
nut. Repeat procedure on opposite side of the tongue.
Coupler:
Mount the coupler (Ref.#29) onto the tongue with one
(1) 1/2 X 4 hex bolt into the rear hole on coupler and
tongue and using (2) 1/2 X 1 hex bolts into the two (2)
front holes on coupler and tongue. Secure with 1/2 flange
lock nuts.
Winch Post:
Secure the winch post to the tongue with three (3) 3/8
X 4 hex bolts and 3/8 flange lock nuts. Mount the winch
handle to the winch using a the special nut provided.
Tighten the winch post in a location that best fits your
water craft.
Axle:
Place one of the spring bushings (Ref.#18) into the
rear of the spring bracket and secure with a 9/16 X 3-1/4
hex bolt and 9/16 lock nut. Repeat on the other side.
Position the axle under the frame, then hook the spring
loop around the bushing just installed. Raise the axle
assembly up so the front of the springs line up with the
front spring bracket hole. Insert the other two (2) 9/16 X
3-1/4 hex bolts and 9/16 lock nuts. Tighten all nuts and
bolts, but do not over tighten. Allow the spring room
enough to move.
Mount the tires and rims using 80-90 ft. lbs. torque on
lug nuts using proper tightening procedures.
Bunk:
Mount the 3-13/16 bunk support brackets (Ref.#57) to
the front crossmember using 3/8 X 2-3/4 hex bolts.
Mount the 2-7/8 bunk support brackets (Ref.#93) on the
rear crossmember using 3/8 X 3-3/4 hex bolts. Mount the
bunk support brackets in a location that would best fit the
hull formation of your watercraft. Secure with 3/8 flange
continue to page 4
Bundles Required