ShoreLand'r LIB15 - Manual (Page 7)

1 6240610 FENDER SUPPORT BRKT ...................... 4
2 62780-- SPRING BRACKET BOLT ON .................. 2
3 65060-- AXLE WMENT (64 WIDE FISHING) ......... 1
4 0110107 HH 1/2-13 X 3 CS GR5 ............................. 2
5 0110170 HH 9/16-18 X 3 1/4 CS GR5 ..................... 2
6 0120052 HH 3/8-16 X 2 3/4 CS GR5 ....................... 4
7 0210102 CARR 3/8-16 X 1 GR5 .............................. 1
8 0310060 SUB 3/8-16 X 2 3/16 X 1 3/4 ..................... 4
9 1340095 WASHER USS FLAT 3/8 ........................... 4
10 1340206 WASHER 1.5 OD X .765 ID X .186/.206 .. 2
11 1410230 HEX LUGNUT 1/2-20 3/4 OD Z&U ........... 10
12 1440101 FLANGE LOCKNUT SMALL 3/8-16 .......... 13
13 1440102 FLANGE LOCKNUT SMALL 1/2-13 .......... 2
14 1440259 HEX LOCKNUT 9/16-18 GRA ................... 2
15 1440349 HEX NUT SLOTTED PLAIN ..................... 2
16 1540038 COTTER KEY 1/8 X 1 1/2 ......................... 2
17 3510123 FENDER FISHING TADPULL POLY ....... 2
18 3510132 AXLE PAD 12IN BLK ................................ 1
19 4300206 5.30X12 C TIRE/GALV MOD RIM ............. 2
-- 4300184 5.30 X 12 C TIRE/MSILVER MOD RIM .... 2
-- 4300209 ST155/80R13C TIRE/GALV DIR RIM ....... 2
-- 4300210 ST155/80R13C TIRE/MSILVER DIR RIM 2
20 4410087 SPINDLE SLEEVE - 1 1/16 ....................... 2
21 4410247 BEARING BUDDY - STAINLESS STEEL . 2
22 4410275 SEAL .......................................................... 2
23 4440160 ROLLER BEARING 1 1/16IN .................. 4
24 4470337 HUB 1 1/16 X 1 1/16 CAST ..................... 2
25 4610010 SLIPPER LEAF SPRING .......................... 2
26 S-2029 SPRING BUSHING SPACER ................... 2
27 S-3387 2" PLASTIC CHANNEL BRACKET ........... 1
Chassis - 15/15A
REF# PART# DESCRIPTION QTY
Made in the USA Midwest Industries, Inc. Ida Grove, IA 51445 (800)859-3028 0002759
www.shorelandr.com REV - 6/01/00
®
REF# PART# DESCRIPTION QTY
Place one of the spring bushings (Ref.#26) into the rear of the
spring bracket (Ref.#2) and secure with a 9/16” X 3-1/4” hex bolt
(Ref.#5) and 9/16” hex lock nut (Ref.#14). Repeat on the other
side. Position the axle (Ref.#3) under the frame, then hook the
spring loop around the bushing just installed. Raise the axle
assembly up so the front of the springs (Ref.#25) line up with the
front spring bracket hole. Insert the other two (2) 9/16” X 3-1/4” hex
bolts and 9/16” hex lock nuts. Tighten all nuts and bolts, but do not
over tighten. Allow the spring room enough to move.
Mount the tires and rim assemblies (Ref.#19) using 80-90 ft. lbs.
tongue on lug nuts (Ref.#11) using proper tightening procedures.
Tire Size & Carrying Capacity Chart
Chassis Tire Load Carrying
Size Range Capacity
15 5.30 X 12 C 1045 lbs. per/tire
15A ST155X80R13 C 1100 lbs. per/tire
Refer to the tire side wall for the correct tire pressure.