ShoreLand'r SLR15A V.2 - Manual (Page 8)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003607
Page 8 Rev B 04/15/2009
Final Assembly Instructions
Remove the small parts from the frame by cutting the bands. Remove
the bolt bag and sort all nuts and bolts by size.
Tongue:
Remove the tongue assembly from the frame bundle and install into
the tongue channel and secure with a 1/2” 4” hex bolt in the side of the
tongue and tongue channel. Secure with a 1/2” flange lock nut.
Tongue Wires:
Install the tongue wire harness through the top forward wire hole and
exit the rear of the tongue channel on the frame. Install grommets and
plug the tongue wire into the frame harness by color.
Run the tongue harness thru the opening in the tongue cover. Place the
tongue cover over the rear of the tongue channel and secure with a 1/2”
x 1 1/2” hex bolt and secure with a 1/2” flat washer and 1/2” flange lock
nut.
Safety Chain:
Insert a 3/8” X 1-1/4” hex bolt with a 3/8” flat washer and safety chain
through the lower hole on the front of the tongue. Secure with a 3/8” flat
washer and 3/8” flange lock nut. Repeat the procedure on the opposite
side of the tongue.
Coupler:
Mount the coupler onto the tongue with one (1) 1/2” X 4” hex bolt into
the rear of the coupler and tongue and using two (2) 1/2” X 1” hex bolts
into the two (2) front holes on the coupler and tongue. Secure with 1/2”
flange lock nuts.
Winch:
Secure the winch post to the tongue with three (3) 3/8” X 4” hex bolts
and 3/8” flange lock nuts. Mount the winch handle to the winch using
the special nut provided. Tighten with winch post in a location that best
fits your water craft.
Keel Roller Assembly:
Open box and remove all parts and hardware bag. Open hardware bag
and sort parts.
Place 64923_ _ front keel guide bracket over front cross member and
align holes in bracket with those in the front cross and insert 3/8” X
3” carriage bolts from rear to front and secure 3/8” flange lock nuts.
Place cradle assembly with pin in center in the rear slot on top of the
previously attached bracket with bent ends facing forward. Take outer
channel assemblies and place on top of bracket aligning holes and
insert 3/8” X 3” hex bolts, secure with 3/8” flange lock nuts. In the slots
in the ends of the channel, insert 3/8” X 5” carriage bolts through cross
member and secure 3/8” flange lock nuts.
Roller Arm Assembly:
Remove parts from hardware box and sort parts.
Slide a swivel block onto each end of the roller arm weldments align-
ing the center hole with the large hole in the round tube. Place a roller
pin weldments over the swivel block align the holes and insert 3/8 x 2
¾” carriage bolts. NOTE: make sure all bolts go in the same direction.
Secure with 3/8 flange lock nuts and tighten only tight enough to secure
the roller pin snugly to the swivel block. This will allow the pin to swivel
so it will conform to the bottom of the boat. Place a ¾” flat washer over
the pin then a roller the spacer and another flat washer and then insert
a cotter key through the hole. Bend both sides of the cotter key out to
hold the roller in place. Repeat for the other rollers.
Mount the roller arm assemblies just created to the rear pivot with the
bolts that go through the roller pins to the center of the trailer. Posi-
tion the roller arm so that the pointed end of the roller arm mounting
tube points toward the side frame of the trailer. For flat bottom boats,
the roller arm assembly may be reversed to decrease the angle of the
rollers. Slide u-bolts around the rear pivot and through the holes of the
mounting plate and secure with 3/8” lock washer and 3/8 hex nuts.
Adjustment may be made by sliding the roller arms in or out on the
rear pivot. Adjustment can also be made by removing the cotter key,
flat washer, spacer, and roller from the roller pin and placing the spacer
next to the inside washer, then the roller, the washer, and re-inserting
the cotter key.
Roller Assembly:
Mount the roller assemblies to the rear pivot in a location that best fits
your watercraft. Secure with 3/8” X 2-7/16” X 4” square u-bolts and
3/8” X 2-7/16” X 4” square u-bolts and 3/8” lock washers and 3/8” hex
nuts.
Axle and Wheel Assembly
Locate the axle for the trailer. Note that there is not a right or left to
the axle assembly. Place one of the springs on top of the spring pad
welded to the axle as shown in Diagram D. Drop two (2) 3/8” x 2-3/16”
x 2” U-bolts over the springs and down through the holes in the spring
pad. Secure with 3/8” flange lock nuts. Repeat this process on the other
spring mounting it so that it is oriented on the axle the same as the first
spring.
Slip a spring bushing spacer into the rear of the spring bracket, align
the bushing with the hole in the bracket and secure in position using a
1/2” x 3” hex bolt and 1/2” flange lock nut. Tighten. Repeat on the other
spring bracket.
Slide the axle assembly under the trailer frame, raise up and slide the
rear of the springs above the bushings just installed. Rotate the as-
sembly up until the front spring eyes align with the front holes in the
spring bracket. Insert a 9/16” x 3-1/4” hex bolt and secure with a 9/16”
lock nut. Tighten. Tighten the U-bolt attaching the springs to the axles
at this time and any other bolts that may have been left loose for ease
of assembly.
Place the tire and wheel assemblies on the hubs and secure with the
1/2” tapered lock nuts.
Tire And Wheel Assemblies
Mount the tire and wheel assemblies using the 1/2” fine threaded ta-
pered lug nuts provided. Tighten to 80-90 ft/lb. of torque using the rota-
tion pattern as shown in the ShoreLandr’s Owners Manual. Re-torque
the lug nuts after 50 miles of driving and then periodically
thereafter.