ShoreLand'r SLB46TBBS V.1 - Manual (Page 8)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003466
Page 8
TRAILER ADJUSTMENTS
The adjustment of the trailer to your boat is very important not only
for the trailer, but also the boat. Failure to do so may lead to poten-
tial failure or damage to either the trailer or boat.
Adjust as follows:
AXLE ADJUSTMENT
The amount of tongue weight on your trailer can be adjusted as
follows:
To lower the tongue weight, adjust the axle assembly forward. To
increase the tongue weight, adjust the axle backward.
The distance that the axle assembly has to be moved will vary be-
cause it is directly related to the weight and center of gravity of the
boat placed on it.
Best towing is achieved when the tongue weight is 5-7% of the total
gross load of the complete unit.
Note: Wire harnesses and brake line lines will need care when
moving the axle assembly.
REAR SUPPORT SYSTEM
Place the boat on the trailer so that the transom is located at the
rear of the support system. On a bunk trailer, the transom of the
boat should be within 1-2” of the end of the bunk. This gives you
maximum support on the transom.
The rear cross member is adjustable forward or backward to allow
the trailer to be adjusted to various length boats. This is accom-
plished by removing the pivot bolt on holds each end of the rear
pivot to the side frame. Reposition the rear pivot arm into the other
hole position predrilled in the side frame.
Reattach the rear pivot to the side frame with the bolts just re-
moved. Tighten.
The wire harness for the three-light identification light must be re-
positioned where it comes from the side frame to the rear pivot to
eliminate slack, and sagging of the wiring.
BUNKS
Make sure the bunks are positioned far enough apart to give your
boat as much stability as possible while transporting. Position the
bunks so they are located just the outside of a strake that your boat
may have. This will help center your boat and assist when loading.
The bunks need be adjusted up high enough to keep the keel from
resting on the center pads. A minimum of one to two inches clear-
ance is desirable.
FRONT BUNK SUPPORT
The front bunks should be adjusted either in or out so that the bunk
will continue to run just to the outside of the strake of the boat.
Adjust the bunks up so that there is approximately 1-2 inches clear-
ance between the keel of the boat and the center cross member
pad.
WINCH POST
Once all other adjustments are complete the winch post can be
adjusted. Slide the winch post base backward on the tongue until
the bow roller comes in contact with the boat.
This bow roller needs to be positioned directly above the boat bow
eye to prevent your boat from moving forward in the event of a sud-
storage. The complete brake system including the axle MUST be
re-bled to ensure that all air has been removed from the brake sys-
tem. For bleeding instructions see the UFP brake bleeding manual
or the ShoreLand’r Disc Brake Manual.
Fill the actuator reservoir with brake fluid and bleed the line per the
instructions in the ShoreLand’r Brake Manual
DUAL AXLE BRAKE INSTALLATION
If your trailer is equipped with dual axle brakes connect the line to
the axle as follows: Cut the tape securing the brake line hose to
the axle. Remove the brass plug from the port in the brass block
on the right brake caliper. Thread the brake hose male end into
the block and tighten to 6-8 ft. lb. or 72-96 in. lb. of torque. DO
NOT OVER TIGHTEN. Over tightening will cause the brass block
to crack and then leak. Attach the brake hoses from the axles to the
spring bracket with the U-shaped hose clip. Once the brake hoses
are secured in place the lines can be attached. Identify which brake
line hose that the side frame brake line tubing will be connected
to. In a dual axle installation it can connected to either one. When
identified, locate the brass tee connector. Screw the male port of
the tee into the brake line hose. Tighten. Next connect the side
frame brake line into the top port on the tee. Connect the two axles
together using the 40” brake line supplied. Thread one end of the
line into the brass tee just installed. Route the line over to the other
axle, form a loop in the line and then connect the other end into the
brake line hose for the second axle.
TIRE & WHEEL ASSEMBLY
Mount the tire and wheel assemblies using the 1/2” fine threaded
tapered lug nuts provided. Tighten to 85-95 ft./lb. torque using the
rotation pattern as shown in the ShoreLandr’s Owners Manual.
Re-torque the lug nuts after 50 miles driving and then periodically
thereafter.