H3C Technologies H3C S12500 Series Switches - Manual (Page 25)

19
Table 17 Specifications for 10-Gigabit SFP+ fiber transceiver modules (2)
Model
Optical parameters
Transmit power
Receive power
SFP-XG-SX-MM850-A –7.3 dBm to –1 dBm –9.9 dBm to +0.5 dBm
SFP-XG-SX-MM850-B –7.3 dBm to –1 dBm –9.9 dBm to +0.5 dBm
SFP-XG-SX-MM850-D –7.3 dBm to –1 dBm –9.9 dBm to +0.5 dBm
SFP-XG-SX-MM850-E –7.3 dBm to –1 dBm –9.9 dBm to +0.5 dBm
SFP-XG-SX-MM850-F1 –7.3 dBm to –1 dBm –9.9 dBm to +0.5 dBm
SFP-XG-LX220-MM1310 –6.5 dBm to +0.5 dBm –6.5 dBm to +1.5 dBm
SFP-XG-LX-SM1310 –8.2 dBm to +0.5 dBm –14.4 dBm to +0.5 dBm
SFP-XG-LX-SM1310-D –8.2 dBm to +0.5 dBm –14.4 dBm to +0.5 dBm
SFP-XG-LX-SM1310-E –8.2 dBm to +0.5 dBm –14.4 dBm to +0.5 dBm
SFP-XG-LH40-SM1550 –4.7 dBm to +4 dBm –15.8 dBm to –1 dBm
SFP-XG-LH40-SM1550-D –4.7 dBm to +4 dBm –15.8 dBm to –1 dBm
SFP-XG-LH80-SM1550 0 dBm to +4 dBm –24 dBm to –7 dBm
SFP-XG-LH80-SM1550-D 0 dBm to +4 dBm –24 dBm to –7 dBm
SFP-FC-8G-SW-MM850
–10 dBm to 0 dBm –13.1 dBm to 0 dBm
–9 dBm to 0 dBm –12.1 dBm to 0 dBm
–8.2 dBm to 0 dBm –11.2 dBm to 0 dBm
SFP-FC-8G-LW-SM1310
–9.5 dBm to –3 dBm –18.2 dBm to –3 dBm
–8.4 dBm to –1 dBm –15.4 dBm to –1 dBm
–8.4 dBm to +0.5 dBm –13.8 dBm to +0.5 dBm
NOTE:
A mode conditioning patch cord is required when you use OM1 or OM2 fiber types on an
SFP-XG-LX220-MM1310. No mode conditioning patch cords are required for OM3 fiber types. For more
information about mode conditioning patch cords, see the IEEE 802.3 standard.
10-Gigabit SFP+ cable
Figure 14 10-Gigabit SFP+ cable