Amped Wireless AP20000G - High Power Wireless-N 600mW Gigabit Dual Band Access Point - Manual

2
Connect your Computer to the Access Point
1 Connect the Access Point to your Router/Network
Connect the Access Point to your
Router’s Network (LAN) port, or a
network switch
Network
Plug in the Power Adapter
Attach the Antennas
Allow up to three (3) minutes for the
Access Point to automatically configure
itself to your network
Modem Internet
Router
(LAN port)
a
b
c
Connect to your
router/switch
Wired Connections:
Scan for available wireless networks on your
PC and connect to one of the following networks:
Wireless Connections:
Attach any Wired Devices to the
Access Point using an Ethernet
cable.
NETWORK ID: Amped_AP_2.4GHz
PASSWORD: wireless
NETWORK ID: Amped_AP_5.0GHz
PASSWORD: wireless
- or -
Congratulations, you’re done!
Note: If your network uses static IP address assignments, you will need to manually configure the settings for your
Access Point. See the instructions on the back to access the configuration menu of the Access Point.
The instructions below are optional. You may now use your Access Point without any additional
configurations. However, if you wish to change any settings (such as network ID and security) for the
Access Point, follow the instructions below to access the configuration menu of the Access Point.
!
1
Optional Configurations: Accessing the Dashboard / Web Menu
Open your Web Browser
If the URL fails to open, then try: http://192.168.80.240
http://setup.ampedwireless.com
Enter the setup web address into your browser:
2
3
Welcome to the Dashboard
The Dashboard provides you with a quick
glance at your system status.
Click on Basic Setup to configure:
System Clock
Wireless Network SSID
Wireless Network Security Key 1
2
3
Connect to the Access Point using a network cable or scan for available wireless networks on your PC
and connect to:
NETWORK ID: Amped_AP_2.4GHz
PASSWORD: wireless
Amped_AP_2.4GHz
NETWORK ID: Amped_AP_5.0GHz
PASSWORD: wireless
Amped_AP_5.0GHz
4
Set the System Clock Time
The System Clock is used for system logs
and setting schedules for Internet access.
Click
Sync to synchronize the System Clock
with the time on your computer.
Click Next to continue.
5
Configure your Wireless Settings
7 Setup Summary
The Setup Summary provides you with
information regarding your current settings.
If you have additional wired or wireless
devices you may connect them at this time.
- or -
The Access Point creates two Wi-Fi networks:
a 2.4GHz Wi-Fi network and a 5.0GHz Wi-Fi
network.
The IDs of your Wi-Fi networks are:
Amped_AP_2.4GHz and Amped_AP_5.0GHz
To change them, enter a new name in the SSID field.
Users connecting wirelessly to the Access Point will
use this ID to identify your Wi-Fi network.
The default Security Key (WPA/WPA2 Mixed
Mode) for both (2.4GHz and 5.0GHz) networks
is: wireless
To change it, enter a new key in the Security Key
field. The key must be at least 8 characters long.
Click Next to apply your settings. The Access
Point will reboot.
The web menu will now apply your settings.
This process may take up to 90 seconds.
Do not refresh the web page. The page will
automatically reload with the summary.
If you are connected wirelessly to the Access
Point, you will need to reconnect after the
Access Point reboots.
30
Need Help? Give us a call.
Phone: 888-573-8820
Email: [email protected]
Web: www.ampedwireless.com/support
?
— R E A D F I R S T —
SETUP GUIDE
High Power Wireless-N 600mW Gigabit Dual Band Access Point
Need Help? Give us a call.
Phone: 888-573-8820
Email: [email protected]
Web: www.ampedwireless.com/support
?
AP20000G
If you have any problems during the installation process,
please contact Amped Wireless Elite Support for further assistance.
v072612