Specifications, Specifications – Studio Technologies 760-03 V.4.15 User Manual
Page 50

Issue 3, April 2015
Model 760-03/77 User Guide
Page 50
Studio Technologies, Inc.
for Surround
Specifications
Model 760-03 Central Controller
General Audio:
Supported Sample Rates: 32, 44.1, 48, 88.2, 96,
176.4, and 192 kHz
Word Length: 24 bits maximum
Internal Processing: 32 bits
Input-to-Output Latency: two samples (e.g., 0.042
milliseconds @ 48 kHz sample rate)
Digital Audio Inputs: 5 (18 audio channels)
Configuration: two surround (5.1) and three stereo
Type: balanced AES3 (110 ohms, 5 Vpp)
Connector—Surround Inputs and Stereo Inputs
A & B: 25-pin female D-subminiature (DB-25F),
AES59-2012-compliant
Connector—Stereo Input C: 3-pin female XLR
Sample Rate Conversion (SRC):
Application: available on Stereo Input C
Input Sample Rate Range: 8 to 216 kHz, limited to
1/6 to 6 times the output sample rate
Latency: 1 millisecond, nominal
Sync Source: configured to follow L/R of currently
selected input or signal connected to sync input
Sync Input:
Compatible Sources: word clock, DARS (AES11),
bi-level video, tri-level video
Jitter: 4 ns pp maximum
Connector: BNC (per IEC 60169-8 Amendment 2)
Termination: 75 ohms, selectable on/off
Digital Monitor Outputs: 16 channels (8 pairs)
Configuration: organized as two surround (5.1)
and two stereo
Dynamic Range: >135 dB
Type: balanced AES3 (110 ohms, 5 Vpp)
Connector: 25-pin female D-subminiature
(DB-25F), AES59-2012-compliant
Analog Monitor Outputs: 8
Configuration: organized as one surround (5.1)
and one stereo (2-channel)
Type: electronically balanced, source impedance
200 ohms
Nominal Level: +4 dBu @ –20 dBFS input source
and level control at maximum setting
Maximum Level: +24 dBu into 2000 (2 k) ohms or
greater
Frequency Response, Digital Inputs to Analog
Monitor Outputs: 10 Hz-20 kHz +0.0/–0.3 dB @
48 kHz sample rate; –3 dB @ 64 kHz
Distortion (THD+N): 0.004%, ref 1 kHz, +4 dBu
output
S/N Ratio: 89 dB, ref +4 dBu output
Dynamic Range: >109 dB
Crosstalk: –98 dB at 1 kHz; –97 dB at 16 kHz,
ref –1 dBFS input
Connector: 25-pin female D-subminiature
(DB-25F), AES59-2012-compliant
Configurable Input Delay: 0 to 340 milliseconds @
48 kHz sample rate (scales up or down depending
on actual sample rate)
Post-Fader Monitor Output Level Offsets:
each surround and stereo channel independently
adjustable in 0.5-dB steps over a ±12-dB range.
(Digital and analog outputs associated with a
specific channel share the same setting.)
Bass Management:
Supported Sample Rates: 44.1, 48, 88.2, and
96 kHz only
Crossover Frequency and Type: –6 dB @ 40, 50,
60, or 80 Hz, symmetrical for low-pass and high-
pass filters, maximally flat
Filter Slope: 12-per-octave or 24 dB-per-octave
Overall Operation: independent on/off selectable
for surround and stereo post-fader monitor outputs